- 您現在的位置：買賣IC網 > PDF目錄2108 > SI51214-A01AFM (Silicon Laboratories Inc)IC CLK GEN FACTORY CONFIG 6TDFN PDF資料下載
參數資料
| 型號： | SI51214-A01AFM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK GEN FACTORY CONFIG 6TDFN |
| 標準包裝： | 100 |
| 類型： | * |
| PLL： | 帶旁路 |
| 輸入： | 時鐘，晶體 |
| 輸出： | CMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 133MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 1.71 V ~ 1.89 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-WFDFN |
| 供應商設備封裝： | 6-TDFN（1.2x1.4） |
| 包裝： | 管件 |
Si51214
6
Preliminary Rev. 0.7
2. Design Considerations
2.1. Typical Application Schematic
2.2. Comments and Recommendations
Decoupling Capacitor:
A decoupling capacitor of 0.1 μF must be used between VDD and VSS on pin 1. Place the
capacitor on the component side of the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin
and to the GND via should be kept as short as possible. Do not use vias between the decoupling capacitor and the
VDD pin.
Series Termination Resistor
: A series termination resistor is recommended if the distance between the outputs
(SSCLK or REFCLK pins) and the load is over 1 inch. The nominal impedance of the SSCLK output is about
30 . Use 20 resistor in series with the output to terminate 50 trace impedance and place 20 resistor as
close to the SSCLK output as possible.
Crystal and Crystal Load:
Only use a parallel resonant fundamental AT cut crystal. Do not use higher overtone
crystals. To meet the crystal initial accuracy specification (in ppm) make sure that external crystal load capacitor is
matched to crystal load specification. To determine the value of CL1 and CL2, use the following formula:
C1 = C2 = 2CL – (Cpin + Cp)
Where: CL is load capacitance stated by crystal manufacturer
Cpin is the Si51214 pin capacitance (4 pF).
Cp is the parasitic capacitance of the PCB traces.
Example
: If a crystal with CL=18 pF is used and Cp=4 pF, by using the above formula, PCin=PCout=[(18 – (4/2)] x
2 = 32 pF. Programming PCin and PCout to 32 pF assures that this crystal sees an equivalent load of 18 pF and no
other external crystal load capacitor is needed. Deviating from the crystal load specification could cause an
increase in frequency accuracy in ppm.
VDD
VSS
XOUT
XIN
FSEL
SSCLK3
VDD
Si51214
0.1F
10F
CL1
CL2
VDD
5K
XIN
XOUT
相關PDF資料 |
PDF描述 |
|---|---|
| SI51219-A01AFT | IC CLK GEN FACTORY CONFIG 8TSSOP |
| SI5310-C-GM | IC CLOCK MULTIPLIER/REGEN 20-QFN |
| SI5316-B-GM | IC PREC JITTER ATTENUATOR 36QFN |
| SI5317A-C-GM | IC CLK JITTER CLEANR PROG 36QFN |
| SI5320-H-BL | IC CLOCK MULT SONET/SDH 63-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Si51214-A01AFMR | 功能描述:時鐘發生器及支持產品 1.8V, 6 TDFN micro- Clk, fact config gen RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| SI51218-EVB | 功能描述:Si51218 - Timing, Clock Generator Evaluation Board 制造商:silicon labs 系列:- 零件狀態:有效 主要用途:計時，時鐘發生器 嵌入式:- 使用的 IC/零件:Si51218 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| Si51219-A01AFT | 功能描述:時鐘發生器及支持產品 8 TSSOP clockgen SL Clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| Si51219-A01AFTR | 功能描述:時鐘發生器及支持產品 8 TSSOP micro-Clock fact config clk gen RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| SI51219-A14AFT | 制造商:Silicon Laboratories Inc 功能描述:8 TSSOP MICRO-CLOCK - Bulk |
發布緊急采購，3分鐘左右您將得到回復。