Reset settings = 0011_0000b (0x30) S36 (ARM1). Alarm 1 (!7 Mo" />
參數資料
型號: SI2400-FS
廠商: Silicon Laboratories Inc
文件頁數: 54/94頁
文件大?。?/td> 0K
描述: IC ISOMODEM SYST-SIDE DAA 16SOIC
標準包裝: 48
系列: ISOmodem®
數據格式: V.21,V.22,V.23,Bell 103,Bell 212A
波特率: 2.4k
電源電壓: 3 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 16-SOIC N
包裝: 管件
配用: 336-1166-ND - BOARD EVAL FOR SI2400 ISOMODEM
Si2400
58
Rev. 1.3
Reset settings = 0011_0000b (0x30)
S36 (ARM1). Alarm 1 (!7 Mode Only)
Bit
D7D6D5D4D3
D2
D1
D0
Name
POF
PON
IDKT
IT
Type
R/W
Bit
Name
Function
7:6
POF
Pulse Off Time.
00 = 25 ms.
01 = 50 ms.
10 = 65 ms.
11 = Use S2C register.
5:4
PON
Pulse On Time.
00 = 25 ms.
01 = 50 ms.
10 = 65 ms.
11 = Use S2B register.
3:2
IDKT
Intermessage Delay and Kissoff Timeout.
This register field defines two parameters. The Intermessage Delay defines the time the Si2400
waits prior to sending a subsequent message. The Kissoff Timeout defines the time the Si2400
waits for a Kissoff Tone prior to declaring that there is no kissoff tone detected.
00 = Intermessage Delay is measured relative to the end of Kissoff and it is a fixed delay
of 2.4 s. The Kissoff Timeout is measured relative to the end of Kissoff and it is a fixed
value of 2 s.
01 = Intermessage Delay is measured relative to the end of Kissoff and it is determined by
S1F[4:0] (IMT). The Kissoff Timeout is measured relative to the end of Kissoff and it is deter-
mined by S1F[7:5] (KOT).
10 = Intermessage Delay is measured relative to the end of the previous message and it is a
fixed delay of 3.4 s. The Kissoff Timeout is measured relative to the end of Kissoff and it is a
fixed value of 2 s.
11 = Intermessage Delay is measured relative to the end of the previous message and it is
determined by S1F[7:5] (KOT). The Kissoff Timeout is measured relative to the end of Kissoff
and it is determined by S1F[7:5] (KOT).
1:0
IT
Interdigit Timing.
The controlled timing between the pulse digits.
00 = The timing between the end of a digit to the start of the next digit is fixed at 660 ms.
01 = The timing between the end of a digit to the start of the next digit is defined by the S2D
register.
10 = The timing between the start of a digit to the start of the next digit is fixed at 800 ms.
11 = The timing between the start of a digit to the start of the next digit is defined by the S2D
register.
Note: S36 is reconfigured as Alarm 1, a bit-mapped register, in !7 mode only. In all other modes, S36 is SKDTL (Second
Kissoff Tone Detect Length).
相關PDF資料
PDF描述
PIC16LC63-04/SO IC MCU OTP 4KX14 PWM 28SOIC
PIC16LC63-04/SP IC MCU OTP 4KX14 PWM 28DIP
PIC16C63/JW IC MCU EPROM 4KX14 PWM 28CDIP
PIC16LC62A-04I/SP IC MCU OTP 2KX14 PWM 28DIP
PIC16C62A-10/SP IC MCU OTP 2KX14 PWM 28DIP
相關代理商/技術參數
參數描述
SI2400-FSR 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R
SI2400-KS 功能描述:電信線路管理 IC 2400b/s System Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI2400-KSR 功能描述:電信線路管理 IC 2400b/s System Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI2400URT-EVB 功能描述:開發板和工具包 - 無線 SI2400 RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:AT32UC3L 核心:AVR32 頻率: 接口類型:USB 工作電源電壓:5 V
SI2401 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM㈢ WITH LOW-COST DAA