- 您現在的位置：買賣IC網 > PDF目錄385840 > SF2D-DC60V POLARISED, MONOSTABLE SAFETY RELAY PDF資料下載
參數資料
| 型號： | SF2D-DC60V |
| 英文描述： | POLARISED, MONOSTABLE SAFETY RELAY |
| 中文描述： | 極化，單穩態安全繼電器 |
| 文件頁數： | 4/5頁 |
| 文件大小： | 247K |
| 代理商： | SF2D-DC60V |
SF relays work to maintain a normal operating state even when the contact welding occur by overloading or short-circuit
If the internal contacts (No. 2, 3, 6, and 7) weld of 4a4b type, the armature becomes non-operational and the contact gaps of each of
the four form
“
a
”
contacts are maintained at greater than 0.5 mm
.020 inch
. Reliable isolation is thus ensured. The 2a2b type operates
in the same way.
Internal Contacts Weld
If the No. 2 contact welds.
Each of the four form
“
a
”
contacts (No. 1, 3, 5,
and 7) maintains a gap of greater than 0.5 mm
.020 inch
.
No.1
No.2
No.3
No.4
No.8
No.7
No.6
No.5
Non-energized
No.1
No.2
No.3
No.4
No.8
No.7
No.6
No.5
Energized (when no. 2 contact is welded)
If the external contacts (No. 1, 4, 5, and 8) weld of 4a4b type, gaps of greater than 0.5 mm
.020 inch
are maintained between adjacent
contacts and the other contacts return by an non-energized.
External Contacts Weld
If the No. 1 contact welds.
The adjacent No. 2 contact maintains a gap of
greater than 0.5 mm
.020 inch
. The other
contacts, because the coil is not energized,
return to their normal return state; each of
form
“
a
”
contacts (No. 3, 5, and 7) maintains a
contact gap of greater than 0.5 mm
each of the form
“
b
”
contacts (No. 4, 6, and 8)
return to a closed state.
;
If external connections are made in series.
Even if one of the contacts welds, the other contacts
operate independently and the contact gaps are
maintained at greater than 0.5 mm
.020 inch
.
No.1
No.2
No.3
No.4
No.8
No.7
No.6
No.5
Energized
No.1
No.2
No.3
No.4
No.8
No.7
No.6
No.5
Non-energized (when no. 1 contact is welded)
Energized
Contact gap
min 0.5 mm
.020 inch
Weld
Non-energized
The table below shows the state of the other contacts. In case of form
“
a
”
contact weld the coil applied voltage is 0 V.
In case of form
“
b
”
contact weld the coil applied voltage is nominal.
Contact Operation Table
No.1
No.2
No.3
No.4
No.8
No.7
No.6
No.5
Contact No.
Terminal No.
No.1 No.2 No.3 No.4
20
–
19 12
–
11 8
–
7 16
–
15
No.5 No.6 No.7 No.8
13
–
14 5
–
6
9
–
10 17
–
18
Note: Contact gaps are shown at the initial state.
If the contact transfer is caused by load switching, it is necessary to check the actual loading.
Contact No.
State of other contacts
3
4
>0.5
≠
>0.5
>0.5
>0.5
>0.5
≠
>0.5
>0.5
≠
>0.5
>0.5: contact gap
is kept at min. 0.5
mm
.020 inch
≠
: contact closed
Empty cells: either
closed or open
Contact No.
1
2
5
6
≠
7
8
≠
Welded
contact
No.
1
2
3
4
5
6
7
8
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
≠
>0.5
>0.5
>0.5
>0.5
>0.5
≠
≠
≠
≠
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
>0.5
≠
≠
>0.5
相關PDF資料 |
PDF描述 |
|---|---|
| SF4D-DC12V | POLARISED, MONOSTABLE SAFETY RELAY |
| SF4D-DC24V | POLARISED, MONOSTABLE SAFETY RELAY |
| SF4D-DC48V | POLARISED, MONOSTABLE SAFETY RELAY |
| SF4D-DC5V | POLARISED, MONOSTABLE SAFETY RELAY |
| SF4D-DC60V | POLARISED, MONOSTABLE SAFETY RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SF2-DEV-KIT | 制造商:Microsemi Corporation 功能描述:SMARTFUSION2 DEVELOPMENT KIT - Boxed Product (Development Kits) 制造商:Microsemi Corporation 功能描述:Development Kit for SmartFusion2 System-on-Chip (SoC) FPGAs |
| SF2-DEV-KIT-PP-1 | 制造商:Microsemi Corporation 功能描述:KIT DEV FOR SMARTFUSION2 制造商:Microsemi Corporation 功能描述:SmartFusion2 SoC FPGA Development Kit |
| SF2DPK | 制造商:General Electric Company 功能描述:GROUND STRAPS |
| SF2-EH TOP CAP | 制造商:Panasonic Electric Works 功能描述: |
| SF2-EH12 | 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:SENSOR 12CH 10MM PNP 24VDC 制造商:Panasonic Industrial Company 功能描述:SENSOR 12CH 10MM PNP 24VDC |
發布緊急采購，3分鐘左右您將得到回復。