參數資料
型號: SC28L92A1A,512
廠商: NXP Semiconductors
文件頁數: 24/73頁
文件大?。?/td> 0K
描述: IC UART DUAL W/FIFO 44-PLCC
標準包裝: 26
系列: IMPACT
特點: 故障啟動位檢測
通道數: 2,DUART
FIFO's: 16 字節
電源電壓: 3.3V,5V
帶自動流量控制功能:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 44-LCC(J 形引線)
供應商設備封裝: 44-PLCC
包裝: 管件
其它名稱: 935263293512
SC28L92A1A
SC28L92A1A-ND
30
2552K–AVR–04/11
ATmega329/3290/649/6490
This clock may be selected as the system clock by programming the CKSEL Fuses as shown in
Table 8-7 on page 30. If selected, it will operate with no external components. During reset,
hardware loads the pre-programmed calibration value into the OSCCAL Register and thereby
automatically calibrates the RC Oscillator. The accuracy of this calibration is shown as Factory
By changing the OSCCAL register from SW, see “OSCCAL – Oscillator Calibration Register” on
page 32, it is possible to get a higher calibration accuracy than by using the factory calibration.
The accuracy of this calibration is shown as User calibration in Table 28-2 on page 329.
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section “Calibration Byte” on page 296.
Note:
1. The device is shipped with this option selected.
2. The frequency ranges are preliminary values.
3. If 8MHz frequency exceeds the specification of the device (depends on V
CC), the CKDIV8
Fuse can be programmed in order to divide the internal frequency by 8.
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Note:
1. The device is shipped with this option selected
.
Table 8-7.
Internal Calibrated RC Oscillator Operating Modes
Frequency Range(2) (MHz)
CKSEL3..0
7.3 - 8.1
0010
Table 8-8.
Start-up times for the internal calibrated RC Oscillator clock selection
Power Conditions
Start-up Time from Power-
down and Power-save
Additional Delay from
Reset (VCC = 5.0V)
SUT1..0
BOD enabled
6 CK
14CK
00
Fast rising power
6 CK
14CK + 4.1ms
01
Slowly rising power
6 CK
14CK + 65ms(1)
10
Reserved
11
相關PDF資料
PDF描述
VI-B5B-IY CONVERTER MOD DC/DC 95V 50W
D38999/20WD19PC CONN RCPT 19POS WALL MNT W/PINS
ATMEGA169PV-8MCHR MCU AVR 16KB FLASH 16MHZ 64QFN
MS27484T16B8PA CONN PLUG 8POS STRAIGHT W/PINS
D38999/20FB98SN CONN RCPT 6POS WALL MNT W/SCKT
相關代理商/技術參數
參數描述
SC28L92A1A-S 功能描述:UART 接口集成電路 3V-5V 2CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L92A1A-T 功能描述:UART 接口集成電路 3V-5V 2CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L92A1B 功能描述:UART 接口集成電路 UART DUAL W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L92A1B,528 功能描述:UART 接口集成電路 3V-5V 2CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L92A1B,551 功能描述:UART 接口集成電路 IC UART DUAL W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel