參數資料
型號： SC28L198A1A,512
廠商： NXP Semiconductors
文件頁數： 20/57頁
文件大?。?/td> 0K
描述： IC UART OCTAL W/FIFO 84-PLCC
產品培訓模塊： Stand-Alone UARTs
標準包裝： 15
特點： 故障啟動位檢測
通道數： 8
FIFO's： 16 字節
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 84-LCC（J 形引線）
供應商設備封裝： 84-PLCC
包裝： 管件
產品目錄頁面： 828 (CN2011-ZH PDF)
其它名稱： 568-1117-5
935261323512
SC28L198A1A
Philips Semiconductors
Product data sheet
SC28L198
Octal UART for 3.3 V and 5 V supply voltage
2006 Aug 10
27
Table 22. XISR – Xon–Xoff Interrupt Status Register
Bits 7:6
Bits 5:4
Bits 3:2
Bits 1:0
Received X Character Sta-
tus
Automatic X Character transmis-
sion status
TxD flow status
TxD character status
00 – none
01 – Xoff received
10 – Xon received
11 – both received
00 – none
01 – Xon transmitted
10 – Xoff transmitted
11 – Illegal, does not occur
00 – normal
01 – TxD halt pending
10 – re–enabled
11 – flow disabled
00 – normal TxD data
01 – wait on normal data
10 – Xoff in pending
11 – Xon in pending
XISR[7:6] – Received X Character Status. This field can be read to
determine if the receiver has encountered an Xon or Xoff character
in the incoming data stream. These bits are maintained until a read
of the XISR. The field is updated by X character reception
regardless of the state of MR0(7, 3:2) or IMR(4). The field can
therefore be used as a character detector for the bit patterns stored
in the Xon and Xoff Character Registers.
XISR[5:4] – Automatic transmission Status. This field indicates the
last flow control character sent in the Auto Receiver flow control
mode. If Auto Receiver mode has not been enabled, this field will
always read b’00. It will likewise reset to b’00 if MR0(3) is reset. If
the Auto Receiver mode is exited while this field reads b’10, it is the
user’s responsibility to transmit an Xon, when appropriate.
XISR[3:2] – TxD flow Status. This field tracks the transmitter’s flow
status as follows:
00 – normal. The flow control is under host control.
01 – TxD halt pending. After the current character finishes the
transmitter will stop. The status will then change to b’00.
10 – re–enabled. The transmitter had been halted and restarted.
It is sending data characters. After a read of the XISR, it will
return to ”normal” status.
11 – disabled. The transmitter is flow controlled.
XISR[1:0] – TxD character Status. This field allows determination of
the type of character being transmitted. If XISR(1:0) is b’01, the
channel is waiting for a data character to transfer from the TxFIFO.
This condition will only occur for a bit time after an Xon or Xoff
character transmission unless the TxFIFO is empty.
Table 23. WDTRCR – Watch-dog Timer Enable
Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WDT
h
WDT
g
WDT
f
WDT
e
WDT
d
WDT
c
WDT
b
WDT
a
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
This register enables the watch-dog Timer for each of the 8
receivers on the Octal UART.
Table 24. BRGTRU
– BRG Timer Reload
Registers, Upper
Bits 7:0
8 MSB of the BRG Timer divisor.
This is the upper byte of the 16 bit value used by the BRG timer in
generating a baud rate clock
Table 25. BRGTRL
– BRG Timer Reload
Registers, Lower
Bits 7:0
8 LSB of the BRG Timer divisor.
This is the lower byte of the 16 bit value used by the BRG timer in
generating a baud rate clock.
Table 26. BRGTCR – BRG Timer Control Register (BRGTCR)
Bit 7
Bit 6:4
Bit 3
Bit 2:0
BRGTCR b, Register control
BRGTCR b, Clock selection
BRGTCR a, Register control
BRGTCR a, Clock selection
0 – Resets the timer register and
holds it stopped
1 – Allows the timer register to
run.
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk/ 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1b
111 – GIN(1)
0 – Resets the timer register and
holds it stopped.
1 – Allows the timer register to
run.
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk / 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1a
111 – GIN(0)
Start/Stop control and clock select register for the two BRG
counters. The clock selection is for the input to the counters. It is
that clock divided by the number represented by the BRGTU and
BRGTL the will be used as the 16x clock for the receivers and
transmitters. When the BRG timer Clock is selected for the
receiver(s) or transmitter(s) the receivers and transmitters will
consider it as a 16x clock and further device it by 16. In other words
the receivers and transmitters will always be in the 16x ode of
operation when the internal BRG timer is selected for their clock.
相關PDF資料
PDF描述
SC28L91A1B,557 IC UART SINGLE W/FIFO 44-PQFP
SC28L92A1B,557 IC UART DUAL W/FIFO 44-PQFP
SC457MLTRT IC VCORE PWR SUPPLY SNGL 32-MLP
SC5554MVR132 MCU MPC5554 DP ONLY 416-PBGA
SCC2681AE1A44,529 IC UART DUAL 44-PLCC
相關代理商/技術參數
參數描述
SC28L198A1A-S 功能描述:UART 接口集成電路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1BE 功能描述:UART 接口集成電路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1BE,528 功能描述:UART 接口集成電路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1BE,551 功能描述:UART 接口集成電路 3V-5V 8CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1BE,557 功能描述:UART 接口集成電路 3V-5V 8CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*