- 您現在的位置：買賣IC網 > PDF目錄17745 > SC16IS741IPW,118 (NXP Semiconductors)IC UART SGL I2C BUS SPI 16TSSOP PDF資料下載
參數資料
| 型號： | SC16IS741IPW,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SGL I2C BUS SPI 16TSSOP |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
SC16IS741_1
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 — 29 April 2010
14 of 52
NXP Semiconductors
SC16IS741
Single UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
DLL and DLH must be written to in order to program the baud rate. DLL and DLH are the
least significant and most significant byte of the baud rate divisor. If DLL and DLH are both
zero, the UART is effectively disabled, as no baud clock will be generated.
Remark: The programmable baud rate generator is provided to select both the transmit
and receive clock rates.
1.8432 MHz and 3.072 MHz, respectively.
Figure 11 shows the crystal clock circuit reference.
Fig 10. Prescaler and baud rate generator block diagram
Table 7.
Baud rates using a 1.8432 MHz crystal
Desired baud rate
Divisor used to generate
16
× clock
Percent error difference
between desired and actual
50
2304
0
75
1536
0
110
1047
0.026
134.5
857
0.058
150
768
0
300
384
0
600
192
0
1200
96
0
1800
64
0
2000
58
0.69
2400
48
0
3600
32
0
4800
24
0
7200
16
0
9600
12
0
19200
6
0
38400
3
0
56000
2
2.86
BAUD RATE
GENERATOR
LOGIC
MCR[7] = 1
MCR[7] = 0
PRESCALER
LOGIC
(DIVIDE-BY-1)
INTERNAL
OSCILLATOR
LOGIC
002aaa233
XTAL1
XTAL2
input clock
PRESCALER
LOGIC
(DIVIDE-BY-4)
reference
clock
internal
baud rate
clock for
transmitter
and receiver
相關PDF資料 |
PDF描述 |
|---|---|
| 500DLBC-ACH | OSC PROG LVDS 2.5V 250PPM OE SMD |
| W3A41C332KAT2A | CAP ARRAY 4CH 3300PF 100V 0612 |
| 3362U-1-203RLF | TRIMMER 20K OHM 0.5W TH |
| MB2411A2G13-FB | SWITCH PUSH SPDT 0.4VA 28V |
| W3A41C222KAT2A | CAP ARRAY 4CH 2200PF 100V 0612 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16IS74Q900 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs |
| SC16IS750 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support |
| SC16IS750IBS | 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS750IBS,128 | 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16IS750IBS,151 | 功能描述:UART 接口集成電路 UART I2C/SPI RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。