- 您現在的位置：買賣IC網 > PDF目錄385813 > SA9108F (SAMES) TWO PHASE BIDIRECTIONAL POWER/ENERGY METERING IC WITH INSTANTANEOUS PULSE OUTPUT PDF資料下載
參數資料
| 型號： | SA9108F |
| 廠商： | SAMES |
| 元件分類： | 電能質量分析儀 |
| 英文描述： | TWO PHASE BIDIRECTIONAL POWER/ENERGY METERING IC WITH INSTANTANEOUS PULSE OUTPUT |
| 中文描述： | 兩相雙向功率/電能計量IC瞬時脈沖輸出 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 105K |
| 代理商： | SA9108F |
SA9108F
sames
8/12
TYPICAL APPLICATION
In the Application Circuit (Figure 1), the components required for a two phase power
metering application, are shown. Terminated current transformers are used for current
sensing.
The most important external components for the SA9108F integrated circuit are:
C
, C
and C
are the outer loop capacitors for the integrated oversampling A/D
converters. The typical value of C
2
is 2.2nF and the value of C
6
and C
7
is 560μF.
The actual values determine the signal to noise and stability performance. The
tolerances should be within ± 10%.
C
, C
and C
are the inner loop capacitors for the integrated oversampling A/D
converters. The typical value of C
1
, C
3
and C
4
is 3.3nF. Values smaller than 0.5nF and
larger than 5nF should be avoided.
Terminated current sensors (current transformers) are connected to the current sensor
inputs of the SA9108F through current setting resistors (R
5
, R
6
and R
7
, R
8
).
The resistor values should be selected for an input current of 16
μ
A
RMS
into the SA9108F,
at the rated line current.
The values of these resistors should be calculated as follows:
Phase 1:
R
5
= R
6
= (I
L1
/16
μ
A
RMS
) * R
3
/2
Phase 2:
R
7
= R
8
= (I
L2
/16
μ
A
RMS
) * R
4
/2
Where I
LX
=
Secondary CT current at rated conditions.
R
3
and R
4
=
Current transformer termination resistors for the two phases.
R
1
+ R
, R
and R
set the current for the phase 1 voltage sense input. R
+ R
, R
+
P
and R
set the currents for phase 2. The values should be selected so that the input
currents into the voltage sense inputs (virtual ground) are set to 14
μ
A
for nominal line
voltage. Capacitors C8 and C9 are for decoupling and phase compensation.
R
and P
defines all on-chip bias and reference currents. With a total resistance of
24k
, optimum conditions are set. R
+ P
may be varied within ± 10% for calibration
purposes. Any change in resistance will affect the output quadratically (i.e:
R = +5%,
f
= +10%).
XTAL is a colour burst TV crystal (f = 3.5795 MHz) for the oscillator. The oscillator
frequency is divided down to 1.7897 MHz on-chip to supply the digital circuitry and the
A/D converters.
相關PDF資料 |
PDF描述 |
|---|---|
| SA9109B | MONOCHIP SINGLE PHASE BIDIRECTIONAL KILOWATT HOUR METERING IC |
| SA9109BFA | MONOCHIP SINGLE PHASE BIDIRECTIONAL KILOWATT HOUR METERING IC |
| SA9110A | MONOCHIP THREE PHASE BIDIRECTIONAL |
| SA9122EFA | SINGLE PHASE UNIDIRECTIONAL POWER/ENERGY METERING IC WITH SEPERATE 64 SEGMENT LCD DRIVER |
| SA9122EPA | SINGLE PHASE UNIDIRECTIONAL POWER/ENERGY METERING IC WITH SEPERATE 64 SEGMENT LCD DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA9109B | 制造商:SAMES 制造商全稱:SAMES 功能描述:MONOCHIP SINGLE PHASE BIDIRECTIONAL KILOWATT HOUR METERING IC |
| SA9109BFA | 制造商:SAMES 制造商全稱:SAMES 功能描述:MONOCHIP SINGLE PHASE BIDIRECTIONAL KILOWATT HOUR METERING IC |
| SA9110A | 制造商:SAMES 制造商全稱:SAMES 功能描述:MONOCHIP THREE PHASE BIDIRECTIONAL |
| SA-9-115 | 功能描述:焊接工作站設備 Fume Absorber 115V RoHS:否 制造商:OK International 產品:Stands 類型:Soldering and Rework System 最大溫度:+ 55 C 電纜類型:US Cord Included |
| SA9-115 | 制造商:Jonard Industries / OK Industries 功能描述:FUME EXTRACTOR; Features:Benchtop Mounting; Supply Voltage:115VAC ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。