- 您現在的位置：買賣IC網 > PDF目錄225144 > SA58631TK (NXP Semiconductors N.V.) 3 W BTL audio amplifier PDF資料下載
參數資料
| 型號： | SA58631TK |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 音頻放大器 |
| 英文描述： | 3 W BTL audio amplifier |
| 封裝： | SA58631TK<SOT909-1 (HVSON8)|<<http://www.nxp.com/packages/SOT909-1.html<1<Always Pb-free,;SA58631TK<SOT909-1 (HVSON8)|<<http://www.nxp.com/packages/SOT909-1.html<1< |
| 文件頁數： | 20/21頁 |
| 文件大小： | 130K |
| 代理商： | SA58631TK |
SA58631_2
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 02 — 12 October 2007
8 of 21
NXP Semiconductors
SA58631
3 W BTL audio amplier
14.2 BTL application
Tamb =25 °C, VCC = 9 V, f = 1 kHz, RL =8 , Gv = 20 dB, audio band-pass 20 Hz to
20 kHz. The BTL diagram is shown in Figure 3.
The quiescent current has been measured without any load impedance. The total
harmonic distortion + noise (THD+N) as a function of frequency was measured with a
low-pass lter of 80 kHz. The value of capacitor C2 inuences the behavior of PSRR at
low frequencies; increasing the value of C2 increases the performance of PSRR. Figure 6
shows three areas: operating, mute and standby. It shows that the DC switching levels of
the mute and standby respectively depends on the supply voltage level.
The following characterization curves show the room temperature performance for
SA58631 using the demo PCB shown in Figure 21. The 8 curves for power dissipation
versus output power (Figure 10 through Figure 17) as a function of supply voltage, heat
spreader area, load resistance and voltage gain show that there is very little difference in
performance with voltage gain; however, there are signicant differences with supply
voltage and load resistance.
The curves for THD+N versus output power (Figure 18) show that the SA58631 yields the
best power output using an 8
load at 9 V supply. Under these conditions the part
delivers typically 3 W output power for THD+N = 10 %.
(1) No heat spreader.
(2) Top only heat spreader (9.7 cm2 (1.5 in2), 35
m
(1 ounce) copper).
(3) Both top and bottom heat spreader (approximately
32 cm2 (5 in2), 35
m (1 ounce) copper).
Fig 4.
Output power versus supply voltage @
THD+N = 10 %; 32 cm2 (5 in2) heat spreader
Fig 5.
Power dissipation versus ambient temperature
2.0
4.0
6.0
Po
(W)
0
VCC (V)
0
20.0
15.0
5.0
10.0
002aac008
RL = 8
16
002aac009
Tamb (°C)
0
150
100
50
2.0
3.0
1.0
4.0
5.0
P
(W)
0
(1)
(2)
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| SA58632BS | 2 x 2.2 W BTL audio amplifier |
| SA58635UK | 2 x 25 mW class-G stereo headphone driver with I2C-bus volume control |
| SA58637BS | 2 x 2.2 W BTL audio amplifier |
| SA58670ABS | 2.1 W-channel stereo class-D audio amplifier |
| SA58670BS | 2.1 W-channel stereo class-D audio amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA58631TK,115 | 功能描述:音頻放大器 3W BTL AUDIO AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58631TK,118 | 功能描述:音頻放大器 3W BTL AUDIO AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58631TK,157 | 功能描述:音頻放大器 3W BTL AUDIO AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| SA58631TK115 | 制造商:NXP Semiconductors 功能描述:IC AUDIO AMP AB 3W SON-8 |
| SA58631TK-G | 功能描述:音頻放大器 3W BTL AUDIO AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。