- 您現在的位置：買賣IC網 > PDF目錄374675 > SA25F020LEMLFFX (Electronic Theatre Controls, Inc.) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | SA25F020LEMLFFX |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 29/37頁 |
| 文件大?。?/td> | 560K |
| 代理商： | SA25F020LEMLFFX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
SA25F020 Advanced Information
SAIFUN
29
Bulk Erase (BE)
The BE instruction sets all bits in the
memory array to 1. Before it can be
executed, two separate instructions must
be carried out. The device must first be
write enabled via the WREN instruction,
and then a BE sequence, which consists of
four bytes plus data, may be executed. The
address of the memory locations to be
written must be outside the protected
address field location selected by the Block
Write Protection level. During an internal
BE cycle, all commands are ignored except
the RDSR instruction.
A BE instruction requires the following
sequence:
1. After the CSb line is pulled low to
select the device, the BE opcode is
transmitted via the SI line.
2. Erasing begins after the CSb pin is
brought
high.
low-to-high transition must occur
during
the
SCK
immediately after the clock in the
last opcode bit.
The
CSb
pin's
low
time,
As soon as CSb is driven high, the
self-timed BE cycle (whose duration is
defined as T
BE
) is initiated. While the BE
cycle is in progress, the status register may
be read to check the value of the /RDY bit.
The /RDY bit is 1 during the self-timed BE
cycle, and 0 when it is completed. The
WEN bit is reset at some unspecified time
before the cycle is completed. The
instruction sequence is shown in Figure 19.
The SA25F020 is automatically returned to
the Write Disable state at the completion of
a BE cycle.
NOTES:
1. If the device is not write enabled,
the
device
ignores
instruction and returns to the
standby state when CSb is brought
high. A new CSb falling edge is
required to re-initiate the serial
communication.
2. A BE instruction can be applied
only if both Block Protect (BP1,
BP0) bits (as described in Table 8,
page 18, and Table 9, page 21)
are 0.
the
BE
3
2
7
6
5
4
0
Instruction
SCK
SI
1
CS
Figure 19. Bulk Erase (BE) Instruction Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| SA25F020LENFX | 4 Mbit Uniform Sector, Serial Flash Memory |
| SA32-11SRWA | 8mm (0.32INCH) SINGLE DIGIT NUMERIC DISPLAY |
| SA36-11YWA | Multiconductor Cable; Number of Conductors:4; Conductor Size AWG:22; No. Strands x Strand Size:Solid; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Conductor Material:Copper; Outer Diameter:0.141" RoHS Compliant: Yes |
| SA36-11EWA | 9mm(0.36INCH) SINGLE DIGIT NUMERIC DISPLAYS |
| SA36-11 | 9mm(0.36INCH) SINGLE DIGIT NUMERIC DISPLAYS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA25F020LEN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25F020LENF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25F020LENFX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25TFKHL-C1000-D | 制造商:Delkin Devices 功能描述:256MB SECURE DIGITAL, IND TEMP - Trays |
| SA26 | 功能描述:TVS 二極管 - 瞬態電壓抑制器 SA26 Uni-Directional RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
發布緊急采購，3分鐘左右您將得到回復。