- 您現在的位置：買賣IC網 > PDF目錄358386 > SA2007H (SAMES) Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output PDF資料下載
參數資料
| 型號： | SA2007H |
| 廠商： | SAMES |
| 元件分類： | 電能質量分析儀 |
| 英文描述： | Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output |
| 中文描述： | 單相雙向雙元件的功率/脈沖電能計量IC輸出 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 154K |
| 代理商： | SA2007H |
Figure 6: Mains zero crossing on FMO
Figure 7: Output signals in latched mode
P1
P2
INT
RP
FMO
dr-01621
D1, D2
V
I
DR-01283
tDIR
t
t
t
DR-01284
FMO
MAINS
t
V
t
t
Positive energy flow, when voltage sense and both current
sense input are in phase, is indicated on pin D1 or D2 as a logic
1.
Figure 5 shows the behavior of D1 and D2, when energy
reversal takes place. The time period for the direction signal to
change state, t , is the time it takes for the internal integrator
DIR
to count (down) from its present value to zero. Thus the energy
consumption rate determines the speed of change on the
direction outputs.
Mains zero crossing indication (FMO)
The square wave signal of FMO indicates the polarity of the
mains voltage. Due to comparator offsets, the FMO low to high
transition can occur within a range as shown in figure 6. The
time between successive low to high transitions will be equal to
the mains voltage period.
Interrupt (INT)
While the SA2007H is operating in latched mode (see Output
mode description) an interrupt is generated with the falling
edge of the pulse outputs P1 and P2 (see figure 7). INT is
cleared with a logic 1 on the RP input.
OUTPUT SIGNALS IN LATCHED MODE
Latched mode is selected by setting the OMODE input to logic
1. This mode is used with a micro controller to ensure that any
simultaneous pulses on P1 and P2 are not missed. The
functionality of the latched mode is shown in figure 7.
An interrupt is generated with a falling edge on any of the pulse
output signals P1 and P2. The micro controller needs to scan
the status of the pulse outputs as well as the direction signals
D1 and D2 during its interrupt service routine. The micro
controller clears the interrupt by setting the RP input to a logic
1. The pulse outputs P1 and P2 are cleared along with the
interrupt. Note that energy pulses are inhibited when the
interrupt output is set (during latched mode).
PRELIMINARY
相關PDF資料 |
PDF描述 |
|---|---|
| SA2007HPA | Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output |
| SA2007HSA | Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output |
| SA2007M | Single Phase Power/Energy Metering IC with Tamper Detection |
| SA2007MPA | Single Phase Power/Energy Metering IC with Tamper Detection |
| SA2007MSA | Single Phase Power/Energy Metering IC with Tamper Detection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA2007HPA | 制造商:SAMES 制造商全稱:SAMES 功能描述:Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output |
| SA2007HSA | 制造商:SAMES 制造商全稱:SAMES 功能描述:Single Phase Bidirectional Dual Element Power/Energy Metering IC with Pulse Output |
| SA2007M | 制造商:SAMES 制造商全稱:SAMES 功能描述:Single Phase Power/Energy Metering IC with Tamper Detection |
| SA2007MPA | 制造商:SAMES 制造商全稱:SAMES 功能描述:Single Phase Power/Energy Metering IC with Tamper Detection |
| SA2007MSA | 制造商:SAMES 制造商全稱:SAMES 功能描述:Single Phase Power/Energy Metering IC with Tamper Detection |
發布緊急采購，3分鐘左右您將得到回復。