- 您現在的位置：買賣IC網 > PDF目錄299881 > S82H-15024 (Omron Electronics LLC) Industrial Power Supply with Power Factor Correction PDF資料下載
參數資料
| 型號： | S82H-15024 |
| 廠商： | Omron Electronics LLC |
| 元件分類： | 功率因子校正 |
| 英文描述： | Industrial Power Supply with Power Factor Correction |
| 中文描述： | 工業電源，功率因數校正 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 788K |
| 代理商： | S82H-15024 |
S82H
S82H
6
Operation
Remote Sensing Function
The remote sensing function makes it possible to compensate for
voltage drops caused by load lines. To use this function, remove the
short bar from the remote sensing terminals and wire the Power
Supply and load as shown in the following illustration. The remote
sensing terminals are short-circuited with the short bar before ship-
ping.
(100-/150-W Models)
Load connection lines
Remote sensing connection
(2-conductor shielded wire)
Remove
short bars.
(300-/600-W Models)
Remote sensing connection
(2-conductor shielded wire)
Load connection lines
Remove short bars.
Note:
1. When the voltage drop in the load wiring is large, the
overvoltage protection function might engage just from
the increase in voltage to correct the voltage drop, so be
sure to use high capacity wiring.
2. If the remote sensing terminals are left unconnected, the
high voltage protection function will engage and the out-
put voltage will be cut off. Be sure to firmly tighten the ter-
minal screws.
Remote Control Function
The remote control function enables external signals to turn the out-
put of the Power Supply ON and OFF. To use this function, remove
the short bar from the remote control terminals and connect a switch
or transistor to the Power Supply as shown in the following illustra-
tion. The remote control terminals are short-circuited with the short
bar before shipping.
*Use a transistor with VCE > 20 V and IC > 5 mA.
Remove
short bars.
Tr*
Level
Output voltage
L (0.8 V max.)
ON
H (2 V min.)
OFF
Note:
No output will be produced if the terminals are left uncon-
nected. Be sure to firmly tighten the terminal screws.
Fan Alarm Function
(300- and 600-W Models Only)
When the speed of the internal fan drops, the fan alarm output
(SPST-NO) will turn ON (shorted) and after 5 seconds, the output
voltage will be turned off.
The relay contacts must be used with 1 A at 30 V or 1 A (125 VA) at
250 VAC.
FAN
ALM
Normal condition
FAN
ALM
Alarm condition
相關PDF資料 |
PDF描述 |
|---|---|
| S82H-P10005 | Industrial Power Supply with Power Factor Correction |
| S82H | Industrial Power Supply with Power Factor Correction |
| S8627-01A | LOGIC OUTPUT PHOTO DETECTOR |
| S8753 | PHOTO DIODE |
| S9868 | PIN PHOTO DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S82H3124 | 制造商:Omron Electronic Components LLC 功能描述:AC/DC Power Supply Single-OUT 24V 0.6A 15W 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:AC/DC Power Supply Single-OUT 24V 0.6A 15W |
| S82H3305 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:AC/DC Power Supply Single-OUT 5V 6A 30W |
| S82H3312 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:AC/DC Power Supply Single-OUT 12V 2.5A 30W |
| S82H3324 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:AC/DC Power Supply Single-OUT 24V 1.3A 30W |
| S82H-3324 | 功能描述:線性和開關式電源 Suggest S8VM-03024-C RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
發布緊急采購，3分鐘左右您將得到回復。