- 您現在的位置：買賣IC網 > PDF目錄368612 > S6A0072 (SAMSUNG SEMICONDUCTOR CO. LTD.) 16COM/40SEG DOT MATRIX LCD CONTROLLER & DRIVER PDF資料下載
參數資料
| 型號： | S6A0072 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 16COM/40SEG DOT MATRIX LCD CONTROLLER & DRIVER |
| 中文描述： | 16COM/40SEG點陣LCD控制器 |
| 文件頁數： | 6/32頁 |
| 文件大小： | 268K |
| 代理商： | S6A0072 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
S6A0072 16COM/40SEG DOT MATRIX LCD CONTROLLER & DRIVER
6
FUNCTION DESCRIPTION
SYSTEM INTERFACE
This chip consists of two kinds of interface type with MPU: 4-bit bus and 8-bit bus. 4-bit bus and 8-bit bus is
selected by DL bit of function set in the instruction register. During read or write operation, two 8-bit registers are
used. One is the data register (DR), the other is the instruction register (IR). The data register (DR) is used as a
temporary data storage place for being written into or read from DDRAM/CGRAM, target RAM is selected by
RAM address setting instruction. Each internal operation, reading from or writing into RAM, is done automatically.
Thus, after MPU reads DR data, the data in the next DDRAM/CGRAM address is transferred into DR
automatically. Also after MPU writes data to DR, the data in DR is transferred into DDRAM/CGRAM
automatically. The Instruction register (IR) is used only to store instruction code transferred from MPU. MPU
cannot read data from instruction register. The register selection depends on RS input pin setting in both 4-bit bus
mode.
Table 1. Various Kinds Of Operations According to RS and R/W Bits
RS
0
0
1
1
R/W
0
1
0
1
Operation
Instruction write operation (MPU writes Instruction code into IR)
Read busy flag (DB7) and address counter (DB0 - DB6)
Data write operation (MPU writes data into DR)
Data read operation (MPU reads data from DR)
BUSY FLAG (BF)
BF = "High" indicates that the internal operation is being processed. So during this time the next instruction
cannot be accepted. BF can be read, when RS = Low and R/W = High (Read instruction Operation), through DB7
port.
Before executing the next instruction, be sure that BF is not High.
ADDRESS COUNTER (AC)
Address Counter (AC) stores the address of DDRAM/CGRAM that are transferred from IR. After writing into
(reading from) DDRAM/CGRAM data, AC is increased (decreased) by 1 automatically. When RS = "Low", and
R/W = "High", AC value can be read through DB0 - DB6 ports.
相關PDF資料 |
PDF描述 |
|---|---|
| S6B0086 | 80 CH SEGMENT / COMMON DRIVER FOR DOT MATRIX LCD |
| S6B0107 | 64CH COMMON DRIVER FOR DOT MATRIX LCD |
| S6B0108 | 64 CH SEGMENT DRIVER FOR DOT MATRIX LCD |
| S6B0708 | 64COM/128SEG GRAPHIC DRIVER FOR DOT MATRIX LCD |
| S6B0716X01-C0C8 | CAT5E PATCH CORD 3 FOOT BLUE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S6A0073 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:40 CH SEGMENT/COMMON DRIVER FOR DOT MATRIX LCD |
| S6A0074 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:34COM/80SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD |
| S6A0075 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:100 SEG / 34 COM DRIVER & CONTROLLER FOR DOT MATRIX LCD |
| S6A0078 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:120 SEG / 34 COM DRIVER & CONTROLLER FOR DOT MATRIX LCD |
| S6A0079 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:34COM/120SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD |
發布緊急采購，3分鐘左右您將得到回復。