- 您現在的位置：買賣IC網 > PDF目錄385803 > S29NS256P0PBJW003 (SPANSION LLC) MirrorBit Flash Family PDF資料下載
參數資料
| 型號： | S29NS256P0PBJW003 |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | 16M X 16 FLASH 1.8V PROM, 80 ns, PBGA64 |
| 封裝： | 6.20 X 7.70 MM , LEAD FREE, TFBGA-64 |
| 文件頁數： | 33/86頁 |
| 文件大小： | 2234K |
| 代理商： | S29NS256P0PBJW003 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
February 20, 2007 S29NS-P_00_A1
S29NS-P MirrorBit
TM
Flash Family
33
D a t a
S h e e t
( A d v a n c e
I n f o r m a t i o n )
Notes
1. The addresses are latched by rising edge of CLK.
2. CR1.0 to CR1.3 and CR1.5 to CR1.15 = 1 (Default).
3. A software reset command is required after read command.
4. CR0.3 is ignored if in continuous read mode (no wrap around).
6.4
Autoselect
The Autoselect is used for manufacturer ID, Device identification, and sector protection information. This
mode is primarily intended for programming equipment to automatically match a device with its corresponding
programming algorithm. The Autoselect codes can also be accessed in the system. When verifying sector
protection, the sector address must appear on the appropriate highest order address bits (see
Table 6.12
).
The remaining address bits are don't care. The most significant four bits of the address during the third write
cycle select the bank from which the Autoselect codes are read by the host. All other banks can be accessed
normally for data read without exiting the Autoselect mode.
CR1.0
Programmable
Wait State
(Note 1)
0000
=
initial data is
valid on the
2nd
rising
CLK edge
AVD# transition
to V
IH
0001
3rd
CR0.13
0010
4th
0011
5th
CR0.12
0100
6th
0101
7th
CR0.11
0110
=
Reserved
0111
1000
=
initial data is
valid on the
8th
rising
CLK edge
AVD# transition
to V
IH
1001
9th
…
1101
=
initial data is
valid on the
13th
rising
CLK edge
AVD# transition
to V
IH
(Default)
1110
=
Reserved
1111
CR0.10
RDY
Polarity
0 = RDY signal is active low
1 = RDY signal is active high (Default)
CR0.9
Reserved
(Not used)
0 = Reserved
1 = Reserved (Default)
CR0.8
RDY
0 = RDY active one clock cycle before data
1 = RDY active with data (Default)
CR0.7
Reserved
(Not used)
0 = Reserved
1 = Reserved (Default)
CR0.6
Reserved
(Not used)
0 = Reserved
1 = Reserved (Default)
CR0.5
Reserved
(Not used)
0 = Reserved (Default)
1 = Reserved
CR1.4
Output Drive
Strength
0 = Full Drive= Current Driver Strength (Default)
1 = Half Drive
CR0.4
RDY Function
0 = RDY (Default)
1 = Reserved
CR0.3
Burst Wrap
Around
0 = No Wrap Around Burst
1 = Wrap Around Burst (Default)
CR0.2
Burst
Length
000 = Continuous (Default)
010 = 8-Word Linear Burst
CR0.1
011 = 16-Word Linear Burst
CR0.0
100 = 32-Word Linear Burst
(All other bit settings are reserved)
Table 6.11
Configuration Register
CR Bit
Function
Settings (Binary)
相關PDF資料 |
PDF描述 |
|---|---|
| S29NS256P0SBJW000 | MirrorBit Flash Family |
| S29NS256P0SBJW003 | MirrorBit Flash Family |
| S29NS256PABBJW000 | MirrorBit Flash Family |
| S29NS256PABBJW003 | MirrorBit Flash Family |
| S29NS512P | MirrorBit Flash Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29NS256P0SBJW000 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS256P0SBJW003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS256PABBJW000 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS256PABBJW003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS512P | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
發布緊急采購，3分鐘左右您將得到回復。