參數資料
型號： S29GL128P10FFI012
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
中文描述： 128M X 1 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, 1 MM PITCH, LEAD FREE, FBGA-64
文件頁數： 21/77頁
文件大小： 2121K
代理商： S29GL128P10FFI012
November 8, 2007 S29GL-P_00_A7
S29GL-P MirrorBit
Flash Family
21
D a t a
S h e e t
( P r e l i m i n a r y )
7.6
Autoselect
The Autoselect mode provides
manufacturer ID, Device identification, and sector protection information
,
through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This
mode is primarily intended for programming equipment to automatically match a device to be programmed
with its corresponding programming algorithm (see
Table 7.3
). The Autoselect codes can also be accessed
in-system.
There are two methods to access autoselect codes. One uses the autoselect command, the other applies V
ID
on address pin A9.
When using programming equipment, the autoselect mode requires V
ID
(11.5 V to 12.5 V) on address pin A9.
Address pins must be as shown in
Table 7.2
.
To access Autoselect mode without using high voltage on A9, the host system must issue the Autoselect
command.
The Autoselect command sequence may be written to an address within a sector that is either in the read
or erase-suspend-read mode.
The Autoselect command may not be written while the device is actively programming or erasing.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
sector was previously in Erase Suspend).
It is recommended that A9 apply V
ID
after power-up sequence is completed. In addition, it is recommended
that A9 apply from V
ID
to V
IH
/V
IL
before power-down the V
CC
/V
IO
.
See
Table 12.1 on page 68
for command sequence details.
When verifying sector protection, the sector address must appear on the appropriate highest order address
bits (see
Table 7.4
to
Table 7.5
). The remaining address bits are don't care. When all necessary bits have
been set as required, the programming equipment may then read the corresponding identifier code on
DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register.
相關PDF資料
PDF描述
S29GL128P10FFIR10 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL128P10FFIR12 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL128P10FFIV10 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL128P10FFIV12 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL128P10TAI010 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
相關代理商/技術參數
參數描述
S29GL128P10FFI020 功能描述:閃存 128MB 2.7-3.6V 100ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29GL128P10FFI022 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 100NS 64BGA - Tape and Reel
S29GL128P10FFIS10 功能描述:閃存 128MB 3.0V 100ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29GL128P10FFIS20 制造商:Spansion 功能描述:IC 128M PAGE-MODE FLASH MEMORY - Trays
S29GL128P10FFIS22 制造商:Spansion 功能描述:IC FLASH MEMORY - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*