參數資料
型號： S29GL032M10TAIR02
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 4M X 8 FLASH 3V PROM, 100 ns, PDSO40
封裝： MO-142-EC, TSOP-40
文件頁數： 25/160頁
文件大小： 4727K
代理商： S29GL032M10TAIR02
120
S29GLxxxM MirrorBitTM Flash Family
S29GLxxxM_00A5 April 30, 2004
Pr e l i m i n a r y
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the
time between additional sector erase commands from the system can be as-
sumed to be less than 50 s, the system need not monitor DQ3. See also the
Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of
DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase
algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept addi-
tional sector erase commands. To ensure the command has been accepted, the
system software should check the status of DQ3 prior to and following each sub-
sequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 33 shows the status of DQ3 relative to the other status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these
conditions DQ1 produces a “1”. The system must issue the Write-to-Buffer-Abort-
Reset command sequence to return the device to reading array data. See Write
Buffer section for more details.
Table 33. Write Operation Status
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the
maximum timing limits. Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for
further details.
3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location.
4. DQ1 switches to ‘1’ when the device has aborted the write-to-buffer operation
Status
DQ7
(Note 2)
DQ6
DQ5
(Note 1)
DQ3
DQ2
(Note 2)
DQ1
RY/
BY#
Standard
Mode
Embedded Program Algorithm
DQ7#
Toggle
0
N/A
No toggle
0
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
N/A
0
Program
Suspend
Mode
Program-
Suspend
Read
Program-Suspended
Sector
Invalid (not allowed)
1
Non-Program
Suspended Sector
Data
1
Erase
Suspend
Mode
Erase-
Suspend
Read
Erase-Suspended
Sector
1
No toggle
0
N/A
Toggle
N/A
1
Non-Erase
Suspended Sector
Data
1
Erase-Suspend-Program
(Embedded Program)
DQ7#
Toggle
0
N/A
0
Write-to-
Buffer
Busy (Note 3)
DQ7#
Toggle
0
N/A
0
Abort (Note 4)
DQ7#
Toggle
0
N/A
1
0
相關PDF資料
PDF描述
S29GL032M10TAIR12 MirrorBit Flash Family
S29GL032M10TAIR22 MirrorBit Flash Family
S29GL032M10TAIR32 MirrorBit Flash Family
S29GL032M10TAIR42 CAP .1UF 1000V CER 10% X7R RADL
S29GL032M11TCIR42 2M X 16 FLASH 3V PROM, 110 ns, PDSO48
相關代理商/技術參數
參數描述
S29GL032M10TAIR03 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10TAIR10 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10TAIR12 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10TAIR13 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10TAIR20 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*