- 您現在的位置：買賣IC網 > PDF目錄359757 > S29GL01GP90TFIV10 (Spansion Inc.) 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology PDF資料下載
參數資料
| 型號： | S29GL01GP90TFIV10 |
| 廠商： | Spansion Inc. |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| 中文描述： | 3.0伏只頁面模式閃存具有90納米MirrorBit工藝技術 |
| 文件頁數： | 34/77頁 |
| 文件大小： | 2121K |
| 代理商： | S29GL01GP90TFIV10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
34
S29GL-P MirrorBit
Flash Family
S29GL-P_00_A7 November 8, 2007
D a t a
S h e e t
( P r e l i m i n a r y )
7.7.6
Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming operation or a
“Write to Buffer” programming operation so that data can read from any non-suspended sector. When the
Program Suspend command is written during a programming process, the device halts the programming
operation within 15
μs maximum (5
μs typical) and updates the status bits. Addresses are “don't-cares” when
writing the Program Suspend command.
After the programming operation has been suspended, the system can read array data from any non-
suspended sector. The Program Suspend command may also be issued during a programming operation
while an erase is suspended. In this case, data may be read from any addresses not within a sector in Erase
Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area, then user must use
the proper command sequences to enter and exit this region.
The system may also write the Autoselect Command Sequence when the device is in Program Suspend
mode. The device allows reading Autoselect codes in the suspended sectors, since the codes are not stored
in the memory array. When the device exits the Autoselect mode, the device reverts to Program Suspend
mode, and is ready for another valid operation. See
Autoselect
on page 21
for more information.
After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the write operation status bits, just as in the standard
program operation. See
Write Operation Status
on page 36
for more information.
The system must write the Program Resume command (address bits are “don't care”) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Program Resume command
are ignored. Another Program Suspend command can be written after the device has resumed programming.
Software Functions and Sample Code
The following is a C source code example of using the program suspend function. Refer to the
Spansion Low
Level Driver User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash
memory software development guidelines.
/* Example: Program suspend command */
*( (UINT16 *)base_addr ) = 0x00B0; /* write suspend command */
The following is a C source code example of using the program resume function. Refer to the
Spansion Low
Level Driver User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash
memory software development guidelines.
/* Example: Program resume command */
*( (UINT16 *)base_addr ) = 0x0030; /* write resume command */
Table 7.12
Program Suspend
(LLD Function = lld_ProgramSuspendCmd)
Cycle
Operation
Word Address
Data
1
Write
Base + XXXh
00B0h
Table 7.13
Program Resume
(LLD Function = lld_ProgramResumeCmd)
Cycle
Operation
Word Address
Data
1
Write
Base + XXXh
0030h
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL01GP90TFIV12 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P10FAI010 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P10FAI012 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL128P10FAIR10 | 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL01GP90TFIV12 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology |
| S29GL01GS | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family |
| S29GL01GS10DFI020 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family |
| S29GL01GS10DFV020 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family |
| S29GL01GS10DHA020 | 制造商:Spansion 功能描述:FLASH, 1GBIT 100NS 64FBGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。