參數資料
型號： S29AL016D70TAI013
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
中文描述： 1M X 16 FLASH 3V PROM, 70 ns, PDSO48
封裝： MO-142DDD, TSOP-48
文件頁數： 34/58頁
文件大?。?/td> 1037K
代理商： S29AL016D70TAI013
34
S29AL016D
S29AL016D_00_A2 December 17, 2004
P r e l i m i n a r y
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified inter-
nal pulse count limit. Under these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was not successfully
completed.
The DQ5 failure condition may appear if the system tries to program a “1” to a
location that is previously programmed to “0.”
Only an erase operation can
change a “ 0” back to a “ 1.”
Under this condition, the device halts the opera-
tion, and when the operation has exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue the reset command to return
the device to reading array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not an erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If additional sectors are selected for
erasure, the entire time-out also applies after each additional sector erase com-
mand. When the time-out is complete, DQ3 switches from “0” to “1.” The system
may ignore DQ3 if the system can guarantee that the time between additional
sector erase commands will always be less than 50
μ
s. See also the
Sector Erase
Command Sequence
section.
After the sector erase command sequence is written, the system should read the
status on DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If DQ3 is “1”, the internally
controlled erase cycle has begun; all further commands (other than Erase Sus-
pend) are ignored until the erase operation is complete. If DQ3 is “0”, the device
will accept additional sector erase commands. To ensure the command has been
accepted, the system software should check the status of DQ3 prior to and fol-
lowing each subsequent sector erase command. If DQ3 is high on the second
status check, the last command might not have been accepted.
Table 10
shows
the outputs for DQ3.
Table 10. Write Operation Status
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing
limits. See
DQ5: Exceeded Timing Limits
for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
Operation
Embedded Program Algorithm
Embedded Erase Algorithm
Reading within Erase
Suspended Sector
Reading within Non-Erase
Suspended Sector
Erase-Suspend-Program
DQ7
(
Note 2
)
DQ7#
0
DQ6
Toggle
Toggle
DQ5
(
Note 1
)
0
0
DQ3
N/A
1
DQ2
(
Note 2
)
No toggle
Toggle
RY / BY #
0
0
Standard
Mode
Erase
Suspend
Mode
1
No toggle
0
N/A
Toggle
1
Data
Data
Data
Data
Data
1
DQ7#
Toggle
0
N/A
N/A
0
相關PDF資料
PDF描述
S29AL016D70TAI020 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TAI023 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TFI010 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TFI013 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TFI020 16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
相關代理商/技術參數
參數描述
S29AL016D70TAI020 制造商: 功能描述: 制造商:undefined 功能描述:
S29AL016D70TAI023 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TFI010 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016D70TFI010H 制造商:Spansion 功能描述:Cut Tape
S29AL016D70TFI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*