- 您現在的位置：買賣IC網 > PDF目錄382471 > S21S07ACTR (意法半導體) SCSI TERMINATOR PDF資料下載
參數資料
| 型號： | S21S07ACTR |
| 廠商： | 意法半導體 |
| 英文描述： | SCSI TERMINATOR |
| 中文描述： | SCSI端接 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 177K |
| 代理商： | S21S07ACTR |
ST21S07A
4/10
FUNCTIONAL DESCRIPTION
The ST21S07A consists of a bandgap reference,
buffer amplifier, and nine termination resistors
Figure 1). The bandgap reference circuit produces
a precise 1.25V level which is fed to a buffer
amplifier. The buffer produce a 2.85V level and is
capable of sourcing at least 24mA into each of the
termination resistors when the signal line is low
(active). When the driver for a given signal line
turns off, the terminator will pull the signal line to
2.85V (quiescent state). To handle actively
negated SCSI signals, the buffer can sink 200mA.
When all lines settle in the quiescent state, the
regulator will consume about 1.5mA. When the
ST21S07A is put into power-down mode by
bringing PD low, the power-down circuitry will turn
off the transistors on each signal line. This will
isolated the ST21S07A from the signal lines and
effectively remove it from the circuit. The
power-down pin (PD) has an internal pull-up
resistor.To place the ST21S07A into an active
state, the PD pin should be left open circuited.
To ensure proper operation, both the TERMPWR1
and TERMPWR2 pins must be connected to the
SCSI bus TREMPWR line and both the VREF1
and VREF2 pins must be tied together externally.
Each ST21S07A requires a 4.7
μ
F capacitor
connected between the VREF pins and ground.
Figure 2 details a typical SCSI bus configuration.
In an 8-bit wide SCSI bus arrangement ("A"
Cable), two ST21S07A’s would be needed at each
end of the SCSI cable in order to terminate the 18
active signal lines. In a 16-bit SCSI bus
arrangement ("P" Cable), three ST21S07A’s
would be need at each end of the SCSI cable in
order to terminate the 27 active signal lines.
Figure 1 :
Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| S25A3100 | THREE PHASE FULL WAVE BRIDGE RECTIFIER ASSEMBLY |
| S25A380 | THREE PHASE FULL WAVE BRIDGE RECTIFIER ASSEMBLY |
| S25A320S7 | THREE PHASE FULL WAVE BRIDGE RECTIFIER ASSEMBLY |
| S25A340S7 | THREE PHASE FULL WAVE BRIDGE RECTIFIER ASSEMBLY |
| S25A360S7 | THREE PHASE FULL WAVE BRIDGE RECTIFIER ASSEMBLY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S21S180D15JN | 功能描述:工業電流傳感器 +/-200A +/-15V 4000T Current Sensor RoHS:否 制造商:Tamura 電流額定值:400 A 傳感器/變換器類型: 電源電壓:15 V 響應時間: 工作溫度: 準確性: |
| S21SJ | 制造商:EECO Switch 功能描述: |
| S21SPS | 制造商:Panduit Corp 功能描述:42 RU 1070MM STANDARD SIDE PAN 制造商:Panduit Corp 功能描述:42 RU 1070MM DEPTH NET-ACCESS S-TYPE CAB |
| S21SPSW | 制造商:Panduit Corp 功能描述:42 RU 1070MM STANDARD SIDE PAN 制造商:Panduit Corp 功能描述:42 RU 1070MM DEPTH NET-ACCESS S-TYPE CAB |
| S21Z100D15 | 功能描述:板機接口霍耳效應/磁性傳感器 100A 15V RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
發布緊急采購，3分鐘左右您將得到回復。