參數資料
型號： S-875271C
廠商： Seiko Instruments Inc.
英文描述： High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出5.2V,VD檢測7.1V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR))
中文描述： 高耐壓，隨著復位功能，它集成了高精度電壓檢測電路和電壓調整在單一芯片上。（村輸出5.2V，性病檢測7.1V，帶復位功能的高抗電壓穩壓器（芯片內穩壓器集成了高精度的電壓檢測器和穩壓器性病村））
文件頁數： 16/34頁
文件大?。?/td> 239K
代理商： S-875271C
HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION
S-87X Series
Seiko Instruments Inc.
15
4.
Delay Circuit
The delay circuit outputs voltage detector output (V
OR
) with delay after the voltage at V
IN
pin has become release voltage
(+V
DET
) at the rising of V
IN
pin.
In Fig. 9, when Vcd exceeds the reference voltage (Vref), the output
voltage pin V
OR
changes from low to high level, providing delay
output. When the voltage at V
IN
pin falls under the detection voltage (
-V
DET
), the N
2
transistor turns ON, therefore the charge of C
D
is
rapidly discharged and the voltage detector output (V
OR
) changes
from high to low level without delay.
The external capacitor (C
D
) is charged with constant current, and is
practically independent of V
IN
voltage. Its delay time (t
pd
) is
expressed by the following equation:
t
pd
(ms)=Delay coefficient (3.18 min., 5.74 typ., 8.73 max.)×C
D
(nF)
Note
Unless an output delay is needed, keep C
D
pin open.
Do not apply external voltage other than ground potential to
C
D
pins, which may cause IC breakdown.
When designing your printed-circuit board layout, take care
that no leakage current flows to the external capacitor (C
D
),
otherwise the correct delay time may not be obtained.
Because the value of the constant current source I
C
is only
195 nA, C
D
to impedance is high.
5.
Voltage Detection Circuit
The built-in voltage detection circuit (Nch opendrain type) is equivalent to our S-808/809 Series voltage detectors. A pull-up
resistor of about 100 k
is required for output. Since the comparator power of this circuit is supplied from V
IN
pin, this circuit
operates while voltage is applied to V
IN
pin.
The detection voltage of the voltage detector can be selected as follows :
2.1 V to 11.3 V
±2.4%
(0.1V step)
In the S-87XXXXF Series, the release voltage (+V
DET
) accuracy is±1.1%. So, it responds to the application for overcharge
detection of lithium-ion battery packs.
In the S-87XXXXE Series, the input voltage monitoring pin of the voltage detector is externally connected as the SENSE pin.
Because this pin is configured by a resistor only, temporary current such as a through-type current does not flow.
Consequently, even when resistor R
IN
is inserted between input power supply and V
IN
pin, the input power voltage can be
accurately monitored by connecting the SENSE pin to the input power supply. Also, when a drop in the SENSE pin input
voltage is detected, the voltage detector generates a reset signal. At the same time, it powers off the voltage regulator.
Notes:
As shown in Figure 11, when connecting V
OR
output to V
PF
pin in the S-87XXXXC Series or connecting SENSE
pin to V
IN
pin in the S-87XXXXE Series, the following phenomena occur if R
IN
is connected between input
voltage and V
IN
pin. Be careful.
At the time of voltage detection, the voltage regulator is shutdown and load current is cut. Therefore, V
IN
voltage increases by
V
IN
= I
IN
×R
IN
, where the current flowing into R
IN
is set to I
IN
. Hence, if
V
IN
exceeds
hysterisis width Vhys, oscillation starts immediately after detection and continues. It is necessary to set
V
IN
less than Vhys.
At the time of voltage release, the voltage regulator is powered on and load current flows. Therefore, if
V
IN
exceeds hysterisis width Vhys, oscillation starts immediately after release and continues. It is
necessary to set
V
IN
less than Vhys. Also at the time of voltage release, the rush current to charge output
Vcd
C
D
N
2
Vref
+
-
V
OR
I
C
Figure 9 Delay
相關PDF資料
PDF描述
S-875635B High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出5.6V,VD檢測3.5V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR))
S-875043A High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出5.0V,VD檢測4.3V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR))
S-873022A HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION
S-875041AUP-AAE-T2 HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION
S-875045AUP-AAB-T2 HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION
相關代理商/技術參數
參數描述
S-875271CUP-AHA-T2 功能描述:線性穩壓器 - 標準 5.2V with 7.1V Detec RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
S-875271CUP-AHAT2G 功能描述:線性穩壓器 - 標準 5.2V with 7.1V Detec RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
S-875294CUP-AHC-T2 功能描述:線性穩壓器 - 標準 5.2V with 9.4V Detec RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
S-875294CUP-AHCT2G 功能描述:線性穩壓器 - 標準 5.2V with 9.4V Detec RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
S-875635BUP-AGA-T2 功能描述:線性穩壓器 - 標準 5.6V with 3.5V Detec RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*