- 您現在的位置：買賣IC網 > PDF目錄374637 > S-875043C (Seiko Instruments Inc.) High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出5.0V,VD檢測4.3V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) PDF資料下載
參數資料
| 型號： | S-875043C |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出5.0V,VD檢測4.3V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
| 中文描述： | 高耐壓，隨著復位功能，它集成了高精度電壓檢測電路和電壓調整在單一芯片上。（村輸出5.0V，性病檢測4.3V的，帶復位功能的高抗電壓穩壓器（芯片內穩壓器集成了高精度的電壓檢測器和穩壓器性病村）） |
| 文件頁數： | 16/34頁 |
| 文件大?。?/td> | 239K |
| 代理商： | S-875043C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION
S-87X Series
Seiko Instruments Inc.
15
4.
Delay Circuit
The delay circuit outputs voltage detector output (V
OR
) with delay after the voltage at V
IN
pin has become release voltage
(+V
DET
) at the rising of V
IN
pin.
In Fig. 9, when Vcd exceeds the reference voltage (Vref), the output
voltage pin V
OR
changes from low to high level, providing delay
output. When the voltage at V
IN
pin falls under the detection voltage (
-V
DET
), the N
2
transistor turns ON, therefore the charge of C
D
is
rapidly discharged and the voltage detector output (V
OR
) changes
from high to low level without delay.
The external capacitor (C
D
) is charged with constant current, and is
practically independent of V
IN
voltage. Its delay time (t
pd
) is
expressed by the following equation:
t
pd
(ms)=Delay coefficient (3.18 min., 5.74 typ., 8.73 max.)×C
D
(nF)
Note
Unless an output delay is needed, keep C
D
pin open.
Do not apply external voltage other than ground potential to
C
D
pins, which may cause IC breakdown.
When designing your printed-circuit board layout, take care
that no leakage current flows to the external capacitor (C
D
),
otherwise the correct delay time may not be obtained.
Because the value of the constant current source I
C
is only
195 nA, C
D
to impedance is high.
5.
Voltage Detection Circuit
The built-in voltage detection circuit (Nch opendrain type) is equivalent to our S-808/809 Series voltage detectors. A pull-up
resistor of about 100 k
is required for output. Since the comparator power of this circuit is supplied from V
IN
pin, this circuit
operates while voltage is applied to V
IN
pin.
The detection voltage of the voltage detector can be selected as follows :
2.1 V to 11.3 V
±2.4%
(0.1V step)
In the S-87XXXXF Series, the release voltage (+V
DET
) accuracy is±1.1%. So, it responds to the application for overcharge
detection of lithium-ion battery packs.
In the S-87XXXXE Series, the input voltage monitoring pin of the voltage detector is externally connected as the SENSE pin.
Because this pin is configured by a resistor only, temporary current such as a through-type current does not flow.
Consequently, even when resistor R
IN
is inserted between input power supply and V
IN
pin, the input power voltage can be
accurately monitored by connecting the SENSE pin to the input power supply. Also, when a drop in the SENSE pin input
voltage is detected, the voltage detector generates a reset signal. At the same time, it powers off the voltage regulator.
Notes:
As shown in Figure 11, when connecting V
OR
output to V
PF
pin in the S-87XXXXC Series or connecting SENSE
pin to V
IN
pin in the S-87XXXXE Series, the following phenomena occur if R
IN
is connected between input
voltage and V
IN
pin. Be careful.
At the time of voltage detection, the voltage regulator is shutdown and load current is cut. Therefore, V
IN
voltage increases by
V
IN
= I
IN
×R
IN
, where the current flowing into R
IN
is set to I
IN
. Hence, if
V
IN
exceeds
hysterisis width Vhys, oscillation starts immediately after detection and continues. It is necessary to set
V
IN
less than Vhys.
At the time of voltage release, the voltage regulator is powered on and load current flows. Therefore, if
V
IN
exceeds hysterisis width Vhys, oscillation starts immediately after release and continues. It is
necessary to set
V
IN
less than Vhys. Also at the time of voltage release, the rush current to charge output
Vcd
C
D
N
2
Vref
+
-
V
OR
I
C
Figure 9 Delay
相關PDF資料 |
PDF描述 |
|---|---|
| S-873022B | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出3.0V,VD檢測2.2V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
| S-873022C | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出3.0V,VD檢測2.2V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
| S-873021B | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出3.0V,VD檢測2.1V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
| S-873021C | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出3.0V,VD檢測2.1V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
| S-873023C | High Withstand-Voltage Regulators With a Reset Function, Which Integrates High-Precision Voltage Detection And Voltage Regulation Circuits On a Single Chip.(VR輸出3.0V,VD檢測2.3V,帶復位功能的高抗電壓穩壓器（芯片內集成了高精度的電壓檢測器VD和穩壓器VR)) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-875043CUP-ACA-T2 | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION |
| S-875043CUP-ACB-T2 | 功能描述:電壓監測器/監控器 5.0V with 4.3V Detec RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| S-875043CUP-ACBT2G | 功能描述:電壓監測器/監控器 5.0V with 4.3V Detec RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| S-875043CUP-ACC-T2 | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION |
| S-875043CUP-ACD-T2 | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:HIGH WITHSTAND-VOLTAGE VOLTAGE REGULATOR WITH RESET FUNCTION |
發布緊急采購，3分鐘左右您將得到回復。