參數資料
型號: S-817B11AY-Z
元件分類: 固定正電壓單路輸出LDO穩壓器
英文描述: 1.1 V FIXED POSITIVE LDO REGULATOR, 1.58 V DROPOUT, PBCY3
封裝: TO-92, 3 PIN
文件頁數: 10/50頁
文件大小: 882K
代理商: S-817B11AY-Z
SUPER-SMALL PACKAGE CMOS VOLTAGE REGULATOR
S-817 Series
Rev.3.0_00
Seiko Instruments Inc.
18
3. Output Voltage Adjustment Circuit (Only for S817B Series (Product without short circuit protection))
GND
V0
R2
R1
VOUT
VIN
VIN
CL
C1
CIN
VSS
S-817
Series
Figure 17
The output voltage can be boosted by using the configuration shown in Figure 17. The output Voltage
(VO) can be calculated using the following equation (VOUT(E):Effective output voltage):
VO
= VOUT(E) × (R1 + R2) ÷ R1 + R2 × ISS
Set R1 and R2 to high values of resistance so as not to be affected by current consumption (ISS).
Capacitor C1 is effective in minimizing output fluctuation at powering on or due to power or load
fluctuation. Determine the optimum value on your actual device. But it is not also recommended to
attach a capacitor between the S-817 Series power source VIN and VSS pin or between output VOUT
and VSS pin because output fluctuation or oscillation at powering on might occur. As shown in Figure
17, a capacitor must be mounted between VIN and GND, and between VOUT and GND.
Precautions
Wiring patterns for the VIN, VOUT and GND pins should be designed so that the impedance is low.
When mounting an output capacitor between the VOUT and VSS pins (CL) and a capacitor for stabilizing
the input between VIN and VSS pins (CIN), the distance from the capacitors to these pins should be as
short as possible.
Note that the output voltage may increase when a series regulator is used at low load current (1.0 A or
less).
Generally a series regulator may cause oscillation, depending on the selection of external parts. The
following conditions are recommended for this IC. However, be sure to perform sufficient evaluation
under the actual usage conditions for selection, including evaluation of temperature characteristics.
Output capacitor (CL) :
0.1
F or more
Equivalent Series Resistance (ESR) :
30
or less
Input series resistance (RIN) :
10
or less
The voltage regulator may oscillate when the impedance of the power supply is high and the input
capacitor is small or an input capacitor is not connected.
The application conditions for the input voltage, output voltage, and load current should not exceed the
package power dissipation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
SII claims no responsibility for any disputes arising out of or in connection with any infringement by
products including this IC of patents owned by a third party.
相關PDF資料
PDF描述
S-817B50AY-T 5 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, PBCY3
S-8204AAB-TCT1G 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
S-8232AYFT-T2 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
S-8233CAFT 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
S-8241ABXMC-GBX-T2 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
相關代理商/技術參數
參數描述
S-817B12AMC-CWB-T2 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:SUPER-SMALL PACKAGE CMOS VOLTAGE REGULATOR
S-817B12AMC-CWBT2G 功能描述:低壓差穩壓器 - LDO LINEAR LDO REG 1.2UA IQ 75MA IOUT RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
S-817B12AMC-CWB-T2G 功能描述:低壓差穩壓器 - LDO 1.2V 1.2uA 2% RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
S-817B12AUA-CWB-T2 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:SUPER-SMALL PACKAGE CMOS VOLTAGE REGULATOR
S-817B12AUA-CWBT2G 功能描述:低壓差穩壓器 - LDO Linear LDO Regulator 1.2uA Iq 75mA Iout RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20