- 您現在的位置：買賣IC網 > PDF目錄385788 > RTL8201CP-LF (Electronic Theatre Controls, Inc.) SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) PDF資料下載
參數資料
| 型號： | RTL8201CP-LF |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
| 中文描述： | SINGLE-CHIP/SINGLE-PORT個10/100M快速以太網PHYCEIVER（自動交叉） |
| 文件頁數： | 14/38頁 |
| 文件大?。?/td> | 512K |
| 代理商： | RTL8201CP-LF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
RTL8201CP
Datasheet
Single-Chip/Port 10/100 Fast Ethernet PHYceiver
9
Track ID: JATR-1076-21 Rev. 1.21
6.2. Register 1 Basic Mode Status Register
Table 10. Register 1 Basic Mode Status Register
Description
1: Enable 100Base-T4 support
0: Suppress 100Base-T4 support
1: Enable 100Base-TX full duplex support
0: Suppress 100Base-TX full duplex support
1: Enable 100Base-TX half duplex support
0: Suppress 100Base-TX half duplex support
1: Enable 10Base-T full duplex support
0: Suppress 10Base-T full duplex support
1: Enable 10Base-T half duplex support
0: Suppress 10Base-T half duplex support
The RTL8201CP will accept management frames with preamble
suppressed.
A minimum of 32 preamble bits are required for the first SMI
read/write transaction after reset. One idle bit is required
between any two management transactions as per IEEE 802.3u
specifications.
1: Auto-negotiation process completed
0: Auto-negotiation process not completed
1: Remote fault condition detected (cleared on read)
0: No remote fault condition detected
When in 100Base-FX mode, this bit means an in-band signal
Far-End-Fault has been detected. See 7.12 Far End Fault
Indication, page 22.
1: Link has not experienced fail state
0: Link experienced fail state
1: Valid link established
0: No valid link established
1: Jabber condition detected
0: No jabber condition detected
Extended Capability 1: Extended register capability
0: Basic register capability only
Address
1:15
Name
100Base-T4
Mode
RO
Default
0
1:14
100Base_TX_ FD
RO
1
1:13
100BASE_TX_HD
RO
1
1:12
10Base_T_FD
RO
1
1:11
10_Base_T_HD
RO
1
1:10~7
1:6
Reserved
MF Preamble
Suppression
RO
1
1:5
Auto Negotiation
Complete
Remote Fault
RO
0
1:4
RO
0
1:3
Auto Negotiation
RO
1
1:2
Link Status
RO
0
1:1
Jabber Detect
RO
0
1:0
RO
1
6.3. Register 2 PHY Identifier Register 1
Table 11. Register 2 PHY Identifier Register 1
Description
PHY identifier ID for software recognition of the RTL8201CP.
Address
2:15~0
Name
PHYID1
Mode
RO
Default
0000
6.4. Register 3 PHY Identifier Register 2
Table 12. Register 3 PHY Identifier Register 2
Description
PHY identifier ID for software recognition of the RTL8201CP.
Address
3:15~0
Name
PHYID2
Mode
RO
Default
8201
相關PDF資料 |
PDF描述 |
|---|---|
| RTL8201CP-VD | SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
| RTL8201CP-VD-LF | SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
| RT | ECONOLINE - DC/DC - CONVERTER |
| S101032SS02BE | Slide Switches |
| S101031SS02B | Slide Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RTL8201CP-VD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
| RTL8201CP-VD-LF | 制造商:WIZnet Co Ltd 功能描述:Physical I/F Chip+Auto-Crossover,Realtek 制造商:Realtek Semiconductor 功能描述: 制造商:WIZnet Co Ltd 功能描述:IC,RTL8201CP-VD-LF 制造商:WIZNET INC 功能描述:IC,RTL8201CP-VD-LF |
| RTL8201CP電路圖-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTL8201CP電路圖-1 |
| RTL8201CP電路圖-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTL8201CP電路圖-3 |
| RTL8201EL | 制造商:Realtek Semiconductor 功能描述:IC,LAN TRANSCEIVER,SINGLE,CMOS,QFP,48PIN,PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。