- 您現在的位置：買賣IC網 > PDF目錄385774 > RT9183H-33GG (Richtek Technology Corporation) Ultra Low Dropout 1.5A Linear Regulator PDF資料下載
參數資料
| 型號： | RT9183H-33GG |
| 廠商： | Richtek Technology Corporation |
| 英文描述： | Ultra Low Dropout 1.5A Linear Regulator |
| 中文描述： | 1.5A的超低壓差線性穩壓器 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 225K |
| 代理商： | RT9183H-33GG |
RT9183
9
DS9183-12 March 2007
www.richtek.com
Input Capacitor
An input capacitance of
10
μ
F is required between the
device input pin and ground directly (the amount of the
capacitance may be increased without limit). The input
capacitor
MUST
be located less than 1 cm from the device
to assure input stability (see PCB Layout Section). A lower
ESR capacitor allows the use of less capacitance, while
higher ESR type (like aluminum electrolytic) require more
capacitance.
Capacitor types (aluminum, ceramic and tantalum) can be
mixed in parallel, but the total equivalent input capacitance/
ESR must be defined as above to stable operation.
There are no requirements for the ESR on the input
capacitor, but tolerance and temperature coefficient must
be considered when selecting the capacitor to ensure the
capacitance will be
10
μ
F over the entire operating
temperature range.
Output Capacitor
The RT9183 is designed specifically to work with very
small ceramic output capacitors. The recommended
minimum capacitance (temperature characteristics X7R or
X5R) are 10
μ
F to 47
μ
F range with 10m
Ω
to 25m
Ω
range
ceramic capacitors between each LDO output and GND for
transient stability, but it may be increased without limit.
Higher capacitance values help to improve transient.
The output capacitor's ESR is critical because it forms a
zero to provide phase lead which is required for loop
stability.
Application Information
Like any low-dropout regulator, the RT9183 series requires
input and output decoupling capacitors. These capacitors
must be correctly selected for good performance (see
Capacitor Characteristics Section). Please note that linear
regulators with a low dropout voltage have high internal
loop gains which require care in guarding against
oscillation caused by insufficient decoupling capacitance.
No Load Stability
The device will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications.
Input-Output (Dropout) Voltage
A regulator's minimum input-to-output voltage differential
(dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines the
useful end-of-life battery voltage. Because the device uses
a PMOS, its dropout voltage is a function of drain-to-source
on-resistance, R
DS(ON)
, multiplied by the load current:
V
DROPOUT
= V
IN
- V
OUT
= R
DS(ON)
×
I
OUT
Current Limit
The RT9183 monitors and controls the PMOS' gate
voltage, minimum limiting the output current to 2A . The
output can be shorted to ground for an indefinite period of
time without damaging the part.
Short-Circuit Protection
The device is short circuit protected and in the event of a
peak over-current condition, the short-circuit control loop
will rapidly drive the output PMOS pass element off. Once
the power pass element shuts down, the control loop will
rapidly cycle the output on and off until the average power
dissipation causes the thermal shutdown circuit to respond
to servo the on/off cycling to a lower frequency. Please
refer to the section on thermal information for power
dissipation calculations.
Capaacitor Characteristics
It is important to note that capacitance tolerance and
variation with temperature must be taken into consideration
when selecting a capacitor so that the minimum required
amount of capacitance is provided over the full operating
temperature range. In general, a good tantalum capacitor
will show very little capacitance variation with temperature,
but a ceramic may not be as good (depending on dielectric
type). Aluminum electrolytics also typically have large
temperature variation of capacitance value.
相關PDF資料 |
PDF描述 |
|---|---|
| RT9183H-33GGF | Ultra Low Dropout 1.5A Linear Regulator |
| RT9183H-33GM | Ultra Low Dropout 1.5A Linear Regulator |
| RT9183H-33GM5 | Ultra Low Dropout 1.5A Linear Regulator |
| RT9183H-33GS | Ultra Low Dropout 1.5A Linear Regulator |
| RT9183H-33PG | Ultra Low Dropout 1.5A Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT9183HGM5 | 功能描述:IC REG LDO ADJ 1.5A TO263-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| RT9183HGS | 制造商:Richtek Technology Corporation 功能描述:IC REG LDO ADJ 1.5A 8SOP 制造商:Richtek Technology Corporation 功能描述:Ultra Low Dropout 1.5A Linear Regulator |
| RT9183HPM5 | 制造商:Richtek 功能描述:1.5A LDO Regulator |
| RT9183HPS | 制造商:Richtek 功能描述:1.5A LDO Regulator |
| RT9186AGF | 功能描述:IC REG LDO ADJ .5A 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。