- 您現在的位置：買賣IC網 > Datasheet目錄56 > RPM841-H16E4A1 (Rohm Semiconductor)MODULE IRDA 115.2KBPS 7-SMD Datasheet資料下載
參數資料
| 型號： | RPM841-H16E4A1 |
| 廠商： | Rohm Semiconductor |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 79K |
| 描述： | MODULE IRDA 115.2KBPS 7-SMD |
| 標準包裝： | 2,500 |
| 系列： | * |
RPM841-H16
Photo Link Module
Rev.B
8/9
Attached components
Recommended values
Part symbol
C1
Recommended value
Notice
1礔, tantalum or ceramic
Ex.) TCFGA1A105M8R (ROHM)
Bigger capacitance is recommended with much noise from power supply
R1
2.2&?%, 1/8W
(VLEDVCC=3V)
At LED Emitting Duty=25%
[LED current set-up method for Remote control mode]
In case of using R1 with different condition from the above, formula is as follows :
LED resistance value : R1[&], LED average consumption current : ILED[mA], Supply voltage : VLEDVCC[V],
minimum necessary of irradiant intensity le1 [mW / sr]
(Including LEDs distribution within ?5deg)
R1=166 ?(VLEDVCC1.31) / le17.2
ILED=Duty ?(VLEDVCC1.31) / (R1+5.8)
Duty : LED duty at emitting
Please set up to be ILED / Duty < 250[mA] (Duty d 25%)
At IrDA Mode, LED current is constantly approximately 50mA.
(Reference) In case of using R1, typical intensity (le1typ) and maximum intensity (le1max) on
axis are described as below.
le1typ=280 ?(VLEDVCC1.31) / (R1+5.8)
le1max=560 ?(VLEDVCC1.31) / (R1+5.8)
Notes
1) LEDVCC (1pin), VCC (6pin)
"
Other power source can be used difference between LEDVCC and VCC.
2) Caution in designing board lay-out
To get maximum potential from RPM841-H16, please keep in mind following instruction.
"
The line of RXD (4pin) should be connected at backside via through hole close to RPM841-H16 pin lead. Better not to
be close to photo diode side (7pin).
襎his is to minimize feedback supplied to photo diode from RXD.
"
As for C1 between 6-7 pin should be placed close to RPM841-H16.
"
Better to be placed more than 1.0cm in radius from photo diode (pin7 side) and also away from the parts which
generates noise, such as DC / DC converter.
3) Notes
"
Please be sure to set up the TX-RC (2pin) and the TXD (3pin) input to be L (under 0.3V) except transmitting data
(for < 90祍, ON duty d 50%).
"
Power down current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode.
"
Please use by the signal format at IrDA operating mode which is specified by IrDA Ver1.2 (2.4k to 115.2kbps). There
might be on error if used by different signal format.
"
Please pay attention to the lens carefully.
Dusts of scratch on the lens may effect the characteristics of product. Please handle it with care.
相關PDF資料 |
PDF描述 |
|---|---|
| RPM870-H14E2 | MODULE IRDA 115.2KBPS 8SMD |
| RPM871-E2 | MODULE IRDA 115.2KBPS 8SMD |
| RPM871-H12E4 | MODULE IRDA 115.2KBPS 8SMD |
| RPM871-H14E2 | MODULE IRDA 115.2KBPS 8SMD |
| RPM872-E2 | MODULE IRDA 115.2KBPS 8SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RPM841-H16E4A2 | 功能描述:MODULE IRDA 115.2KBPS 7-SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| RPM841-H16E4A3 | 功能描述:MODULE IRDA 115.2KBPS 7-SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| RPM851 | 制造商:ROHM 制造商全稱:Rohm 功能描述:IrDA wireless communication transceiver IC (supports Ver.1.0) |
| RPM851A | 制造商:ROHM 制造商全稱:Rohm 功能描述:IrDA wireless communication transceiver IC (supports Ver.1.0) |
| RPM851A-H6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。