- 您現在的位置：買賣IC網 > PDF目錄368524 > RMPA1951-102 (Raytheon Company) 3V PCS CDMA Power Amplifier Module PDF資料下載
參數資料
| 型號： | RMPA1951-102 |
| 廠商： | Raytheon Company |
| 英文描述： | 3V PCS CDMA Power Amplifier Module |
| 中文描述： | 3V的個人通訊CDMA功放模塊 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 200K |
| 代理商： | RMPA1951-102 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised August 27, 2001
Page 4
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
ADVANCED INFORMATION
CAUTION: THIS IS AN ESD SENSITIVE DEVICE.
Precautions to Avoid Permanent Device Damage:
– Cleanliness: Observe proper handling procedures to ensure clean devices and PCBs. Devices should remain
in their original packaging until component placement to ensure no contamination or damage to RF, DC &
ground contact areas.
– Device Cleaning: Standard board cleaning techniques should not present device problems provided that the
boards are properly dried to remove solvents or water residues.
– Static Sensitivity: Follow ESD precautions to protect against ESD damage:
A properly grounded static-dissipative surface on which to place devices.
Static-dissipative floor or mat.
A properly grounded conductive wrist strap for each person to wear while handling devices.
– General Handling: Handle the package on the top with a vacuum collet or along the edges with a sharp pair
of bent tweezers. Avoiding damaging the RF, DC, & ground contacts on the package bottom. Do not apply
excessive pressure to the top of the lid.
– Device Storage: Devices are supplied in heat-sealed, moisture-barrier bags. In this condition, devices are
protected and require no special storage conditions. Once the sealed bag has been opened, devices should
be stored in a dry nitrogen environment.
Device Usage:
Raytheon recommends the following procedures prior to assembly.
– Dry-bake devices at 125
°
C for 24 hours minimum. Note: The shipping trays cannot withstand 125
°
C baking
temperature.
– Assemble the dry-baked devices within 7 days of removal from the oven.
– During the 7-day period, the devices must be stored in an environment of less than 60% relative humidity
and a maximum temperature of 30
°
C
– If the 7-day period or the environmental conditions have been exceeded, then the dry-bake procedure must
be repeated.
Solder Materials & Temperature Profile:
Reflow soldering is the preferred method of SMT attachment. Hand
soldering is not recommended.
–
Reflow Profile
Ramp-up: During this stage the solvents are evaporated from the solder paste. Care should be taken to
prevent rapid oxidation (or paste slump) and solder bursts caused by violent solvent out-gassing. A
typical heating rate is 1- 2°C/sec.
Pre-heat/soak: The soak temperature stage serves two purposes; the flux is activated and the board
and devices achieve a uniform temperature. The recommended soak condition is: 120-150 seconds at
150°C.
Reflow Zone: If the temperature is too high, then devices may be damaged by mechanical stress due to
thermal mismatch or there may be problems due to excessive solder oxidation. Excessive time at
temperature can enhance the formation of inter-metallic compounds at the lead/board interface and
may lead to early mechanical failure of the joint. Reflow must occur prior to the flux being completely
driven off. The duration of peak reflow temperature should not exceed 10 seconds. Maximum soldering
temperatures should be in the range 215-220°C, with a maximum limit of 225°C.
Cooling Zone: Steep thermal gradients may give rise to excessive thermal shock. However, rapid
cooling promotes a finer grain structure and a more crack-resistant solder joint. The illustration below
indicates the recommended soldering profile.
Solder Joint Characteristics:
Proper operation of this device depends on a reliable void-free attachment of the
heatsink to the PWB. The solder joint should be 95% void-free and be a consistent thickness.
Rework Considerations:
Rework of a device attached to a board is limited to reflow of the solder with a heat
gun. The device should not be subjected to more than 225°C and reflow solder in the molten state for more than
5 seconds. No more than 2 rework operations should be performed.
Application
Information
RMPA1951-102
3V PCS CDMA Power
Amplifier Module
相關PDF資料 |
PDF描述 |
|---|---|
| RMPG06 | MINIATURE GLASS PASSIVATED JUNCTION FAST SWITCHING PLASTIC RECTIFIER |
| RMPG06A | MINIATURE GLASS PASSIVATED JUNCTION FAST SWITCHING PLASTIC RECTIFIER |
| RMPG06B | MINIATURE GLASS PASSIVATED JUNCTION FAST SWITCHING PLASTIC RECTIFIER |
| RMPG06D | MINIATURE GLASS PASSIVATED JUNCTION FAST SWITCHING PLASTIC RECTIFIER |
| RMPG06G | MINIATURE GLASS PASSIVATED JUNCTION FAST SWITCHING PLASTIC RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RMPA1959 | 功能描述:射頻放大器 3.4V PCS CDMA PA Module RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| RMPA1959-108 | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| RMPA1963 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:US-PCS CDMA, CDMA2000-1X and WCDMA Power Amplifier Module |
| RMPA1965 | 功能描述:射頻放大器 US-PCS CDMA2000-1X Pwr Edge Amp Mod RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| RMPA1965_06 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:US-PCS CDMA, CDMA2000-1X and WCDMA PowerEdge TM Power Amplifier Module |
發布緊急采購，3分鐘左右您將得到回復。