- 您現在的位置：買賣IC網 > PDF目錄376309 > RHF-24(2) (Texas Instruments, Inc.) LOW-POWER DISSIPATION ADSL LINE DRIVER PDF資料下載
參數資料
| 型號： | RHF-24(2) |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | LOW-POWER DISSIPATION ADSL LINE DRIVER |
| 中文描述： | 低功耗ADSL線路驅動器 |
| 文件頁數： | 20/30頁 |
| 文件大?。?/td> | 1105K |
| 代理商： | RHF-24(2) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
0.1025
0.080
0.178
0.026
0.024
0.021
0.0165
0.450
0.476
.039
0.026
0.120
0.085
PowerPAD and via placement
pad area (0.085 x 0.120) with 15
vias (Via diameter = 0.013)
Vias should go through the board connecting the top layer
PowerPad to any and all ground planes. (The larger the ground
plane, the larger the area to distribute the heat.) Solder resist should
be used on the bottom side ground plane in order to prevent wicking
of the solder through the vias during the reflow process.
All Units in Inches
THS6182
SLLS544G–SEPTEMBER 2002–REVISED NOVEMBER 2004
APPLICATION INFORMATION (continued)
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
However, in this application, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the THS6182 package should make their connection to the internal ground plane with a
complete connection around the entire circumference of the plated through hole.
6. The top-side solder mask should leave exposed the terminals of the package and the thermal pad area with
its five holes. The four larger holes outside the thermal pad area, but still under the package, should be
covered with solder mask.
7. Apply solder paste to the exposed thermal pad area and all of the operational amplifier terminals.
8. With these preparatory steps in place, the THS6182 DWP is simply placed in position and run through the
solder reflow operation as any standard surface-mount component. This results in a part that is properly
installed.
Figure 73. 20-Pin DWP PowerPAD PCB Etch and Via Pattern
The RHF package is similar to the DWP package with respect to PCB mounting procedures. The recommended
PCB layout is as shown in Figure 74.
20
相關PDF資料 |
PDF描述 |
|---|---|
| RI-60 | Ultra-miniature dry-reed switch hermetically sealed in a gas-filled glass envelope |
| RI60 | Ultra-miniature dry-reed switch germetically sealed in a gas-dilled glass envelope |
| RI-ANT-S01C-00 | SERIES 2000 ANTENNAS |
| RI-I01-110A | Tag-it HF Transponder Inlay Square |
| RI-I11-110A | Tag-it HF Transponder Inlay Square |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RHF310 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Rad-hard 400 ??A high-speed operational amplifier |
| RHF310K-01V | 制造商:STMicroelectronics 功能描述: |
| RHF310K1 | 制造商:STMicroelectronics 功能描述:RAD-HARD 400 µA HIGH-SPEED OPERATIONAL AMPLIFIER (EM) - Bulk |
| RHF330 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Rad-hard 1 GHz low noise operational amplifier |
| RHF330K-01V | 制造商:STMicroelectronics 功能描述:SPACE OPERATIONAL AMP NOT DUAL MARKED NO DESC QUAL - Bulk |
發布緊急采購，3分鐘左右您將得到回復。