參數資料
型號: RH1021BMH-7
廠商: LINEAR TECHNOLOGY CORP
元件分類: 基準電壓源/電流源
英文描述: 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 7 V, MBCY8
封裝: METAL CAN, TO-5, 8 PIN
文件頁數: 3/4頁
文件大?。?/td> 103K
代理商: RH1021BMH-7
3
RH1021-7
TABLE 1A: ELECTRICAL CHARACTERISTICS
TABLE 2: ELECTRICAL TEST REQUIRE E TS
UW
MIL-STD-883 TEST REQUIREMENTS
SUBGROUP
Final Electrical Test Requirements (Method 5004)
1*,2,3,4
Group A Test Requirements (Method 5005)
1,2,3,4
Group B and D for Class S, and
1,2,3
Group C and D for Class B
End Point Electrical Parameters (Method 5005)
* PDA Applies to subgroup 1. See PDA Test Notes.
PDA Test Notes
The PDA is specified as 5% based on failures from group A, subgroup 1,
tests after cooldown as the final electrical test in accordance with method
5004 of MIL-STD-883. The verified failures of group A, subgroup 1, after
burn-in divided by the total number of devices submitted for burn-in in
that lot shall be used to determine the percent for the lot.
Linear Technology Corporation reserves the right to test to tighter limits
than those given.
Note 1: Output voltage is measured immediately after turn-on. Changes
due to chip warm-up are typically less than 0.005%.
Note 2: Temperature coefficient is measured by dividing the change in
output voltage over the temperature range by the change in temperature.
Separate tests are done for hot and cold; TMIN to 25°C and 25°C to TMAX.
Incremental slope is also measured at 25
°C.
Note 3: Line and load regulation are measured on a pulse basis. Output
changes due to die temperature change must be taken into account
separately. Package thermal resistance is 150
°C/W for the TO-5 (H)
package.
Note 4: Shunt mode regulation is measured with the input open. With the
input connected, shunt mode current can be reduced to 0mA. Load
regulation will remain the same.
Note 5: RMS noise is measured with a 2-pole highpass filter at 10Hz and a
2-pole lowpass filter at 1kHz. The resulting output is full wave rectified and
then integrated for a fixed period, making the final reading an average as
opposed to RMS. Correction factors are used to convert from average to
RMS and to correct for the nonideal bandpass of the filters. Peak-to-peak
noise is measured with a single highpass filter at 0.1Hz and a 2-pole
lowpass filter at 10Hz. The unit is enclosed in a still-air environment to
eliminate thermocouple effects on the leads. Test time is 10 seconds.
Note 6: Consult factory for units with long term stability data.
Note 7: VIN = 12V, IOUT = 0, TA = 25°C, unless otherwise noted.
Note 8: IOUT(MAX) (Sourcing) is 5mA for exposures greater than
100Krad (Si).
Note 9: VIN = 12V, IOUT = 0, unless otherwise noted.
Note 10: Absolute Maximum Ratings are those values beyond which the
life of a device may be impaired.
15V
–15V
GND
VIN
0.1
F
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
TOTAL DOSE BIAS CIRCUIT
相關PDF資料
PDF描述
RH1083MMK ADJUSTABLE POSITIVE LDO REGULATOR, 2 V DROPOUT, MBFM2
RH137MH 1.2 V-22 V ADJUSTABLE NEGATIVE REGULATOR, MBCY3
RH137MK 1.2 V-22 V ADJUSTABLE NEGATIVE REGULATOR, MBFM2
RH200-P Coreless Coil Current Transducer RH 100~1000-P
RH200-S Coreless Coil Current Transducer RH 100~1000-S
相關代理商/技術參數
參數描述
RH1021C 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Reference
RH1021C-10 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Reference
RH1021C-5 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision Reference
RH1021CM-10 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision 10V Reference
RH1021CM-10H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage Reference