- 您現在的位置：買賣IC網 > PDF目錄374585 > RF9958PCBA (RF Micro Devices, Inc.) CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER PDF資料下載
參數資料
| 型號： | RF9958PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | CDMA/FM TRANSMIT MODULATOR, IF AGC, AND UPCONVERTER |
| 中文描述： | 碼分多址/調頻發射調制器，中頻AGC和上變頻 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 129K |
| 代理商： | RF9958PCBA |
5-96
RF9958
Rev B11 010720
5
M
U
Pin
1
Function
MODE
Description
Selects between CDMA and FM mode. This is a digitally controlled
input. A logic “high” (
≥
V
CC
-0.7V
DC
) selects CDMA mode. A logic “l(fā)ow”
(
<
0.5V
DC
) selects FM mode. In FM mode, this switch enables the FM
amplifier and turns off the I&Q modulator. The impedance on this pin is
30k
. A DC voltage less than or equal to the maximum allowable Vcc
may be applied to this pin when no voltage is applied to the Vcc pins.
Interface Schematic
2
Q SIG
Baseband input to the Q mixer. This pin is DC coupled. The DC level of
0.6V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50k
minimum. A DC voltage less than or equal to
the maximum allowable Vcc may be applied to this pin when no voltage
is applied to the Vcc pins.
3
Q REF
Reference voltage for the Q mixer. This voltage should be the same as
the DC voltage supplied to the Q SIG pin. For maximum carrier sup-
pression, DC voltage on this pin relative to the Q SIG DC voltage may
be adjusted. Input impedance of this pin is 50k
minimum. A DC volt-
age less than or equal to the maximum allowable Vcc may be applied to
this pin when no voltage is applied to the Vcc pins.
Reference voltage for the I mixer. This voltage should be the same as
the DC voltage supplied to the I SIG pin. For maximum carrier suppres-
sion, DC voltage on this pin relative to the I SIG DC voltage may be
adjusted. Input impedance of this pin is 50k
minimum. A DC voltage
less than or equal to the maximum allowable Vcc may be applied to this
pin when no voltage is applied to the Vcc pins.
Baseband input to the I mixer. This pin is DC coupled. The DC level of
0.6V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50k
minimum. A DC voltage less than or equal to
the maximum allowable Vcc may be applied to this pin when no voltage
is applied to the Vcc pins.
See pin 2.
4
I REF
See pin 5.
5
I SIG
6
GND1
Ground connection for all baseband circuits including bandgap, AGC,
flip-flop, modulator and FM amp. Keep traces physically short and con-
nect immediately to ground plane for best performance.
Supply Voltage for the LO1 flip-flop and limiting amp only. This supply is
isolated to minimize the carrier leakage. A 1nF external bypass capaci-
tor is required, and an additional 0.1
μ
F will be required if no other low
frequency bypass capacitors are nearby. The trace length between the
pin and the bypass capacitors should be minimized. The ground side of
the bypass capacitors should connect immediately to ground plane.
One half of the balanced modulator LO1 input. The other half of the
input, LO1-, is AC grounded for single-ended input applications. The
frequency on these pins is divided by a factor of 2, hence the carrier
frequency for the modulator becomes one half of the applied frequency.
The single-ended input impedance is 100
(balanced is 200
). This
pin is NOT internally DC blocked. An external blocking capacitor (1nF
recommended) must be provided if the pin is connected to a device
with DC present. When FM mode is selected, the output of the flip-flop
divider circuit is switched to the AGC amplifier inputs and the modulator
mixers are not used. Note that the frequency deviation input here will
be reduced by a factor of two, due to the frequency divider operation.
One half of the balanced modulator LO1 input. In single-ended applica-
tions (100
input impedance), this pin is AC grounded with a 1nF
capacitor.
7
VCC1
8
LO1+, FM+
9
LO1-, FM-
See pin 8.
60 k
60 k
BIAS
MODE
8 k
8 k
Q SIG
Q REF
BIAS
BIAS
8 k
8 k
I SIG
I REF
BIAS
BIAS
100
100
LO1+, FM+
LO1-, FM-
V
CC1
V
CC1
相關PDF資料 |
PDF描述 |
|---|---|
| RF9986 | PCS LOW NOISE AMPLIFIER/MIXER |
| RF9986PCBA | PCS LOW NOISE AMPLIFIER/MIXER |
| RFD10P03 | 10A, 30V, 0.200W, Logic Level P-Channel Power MOSFET |
| RFD10P03L | 10A, 30V, 0.200W, Logic Level P-Channel Power MOSFET |
| RFD12N06RLESM | 17A, 60V, 0.071 Ohm, N-Channel, Logic Level UltraFET Power MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF-9980P | 制造商: 功能描述: 制造商:undefined 功能描述: |
| RF9986 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:PCS LOW NOISE AMPLIFIER/MIXER |
| RF9986PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:PCS LOW NOISE AMPLIFIER/MIXER |
| RFA 4001-636-211-401 | 制造商:Novotechnik 功能描述: |
| RFA 4001-736-213-421 | 制造商:Novotechnik 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。