- 您現在的位置：買賣IC網 > PDF目錄385767 > RF3000PCBA (RF Micro Devices, Inc.) SPREAD-SPECTRUM BASEBAND MODEM PDF資料下載
參數資料
| 型號： | RF3000PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | SPREAD-SPECTRUM BASEBAND MODEM |
| 中文描述： | 擴譜基帶調制解調器 |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 351K |
| 代理商： | RF3000PCBA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
11-331
RF3000
Rev A4 031216
RF3000 Method of Operation
The transmitter power enable (TX PE) input enables the transmitter process. (Note: Transmit has priority over receive.)
When TX PE is high, the LNA GS signal will be driven low. The TX RDY output indicates the readiness of the RF3000 to
receive data for transmit. Transmitted data is passed into the RF3000 through the TXDATA input and clocked by the
DATA CLK output. The receiver power enable (RX PE) input enables the receiver, and the receive data ready (RX RDY)
signal indicates that received data is upcoming. The RF3000 generates the received data clocks, and outputs the
received data, through the RX DATA output. The receiver port also provides a clear channel assessment (CCA) to the
MAC.
The table below summarizes the operation of the chip. The user should note that RX PE must be High to perform CCA.
IEEE802.11b Transmit Modes
IEEE802.11b DSSS Transmit Modes
The RF3000 supports PSK and CCK DSSS modes defined in IEEE802.11b specification. The RF3000 also supports the
optional short preamble and header format as defined in IEEE802.11b.
The following section describes IEEE802.11b DSSS data transmission. The user must first prepare the applicable con-
trol port registers to determine the mode of operation and the transmission length. The mode of operation must be writ-
ten into Register 1, followed by setting the transmission length (in microseconds). The length is to be written into
Registers 17 (bit 0 only), 18 and 19. Mode byte values for IEEE802.11b modes are summarized below
.
Once the control port values are written, the RF3000 is ready to transmit data. Optionally, the TX length value can be
written during the 128
μ
S of preamble. When the user is ready to transmit, TX PE is driven High. This signals the RF3000
to assemble and transmit the 802.11 preamble and header, as described below.
The preamble and header for 1Mbps mode is always transmitted as 1Mbps BPSK. However for 2Mbps, 5.5Mbps and
11Mbps modes, IEEE802.11b allows a short preamble, which has the preamble, transmitted as 1Mbps BPSK and the
header transmitted as 2Mbps QPSK. The usage of the optional short preamble is selected when the transmission mode
is written to the control port.
TX PE
RX PE
Operation
0
0
Standby mode.
0
1
RX is powered up. CCA circuity is active.
1
0
TX is powered up. Begin TX. CCA is inactive.
1
1
RESERVED
IEEE802.11 DSSS Mode
Mode Byte Value
1Mbps DBPSK
0x00
16
2Mbps DQPSK Long preamble
0x20
16
2Mbps DQPSK Short preamble
0x30
16
5.5Mbps CCK Long preamble
0x40
16
5.5Mbps CCK Short preamble
0x50
16
11Mbps CCK Long preamble
0x60
16
11Mbps CCK Short preamble
0x70
16
Preamble
Header
Data
128 1’s
SFD
(16-bits)
Service
(8-bits)
Signal
(8-bits)
Length
(16-bits)
CRC
(16-bits)
Data
(x-bits)
相關PDF資料 |
PDF描述 |
|---|---|
| RF2046PCBA-41X | GENERAL PURPOSE AMPLIFIER |
| RF2114 | TRI R RECP F FLG SEAL 0-4 |
| RF2114PCBA | MEDIUM POWER LINEAR AMPLIFIER |
| RF2115 | HIGH POWER UHF AMPLIFIER |
| RF2115L | HIGH POWER UHF AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF-3000PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM |
| RF300-12 | 功能描述:高頻/射頻繼電器 12V DC-6GHz .15W RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
| RF300-12/G | 制造商:Teledyne Relays 功能描述:RF RELAY |
| RF3001A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FUELLSTANDSFUEHLER VERT |
| RF-3001A | 制造商:Assemtech 功能描述:VERTICAL FLOAT 制造商:Comus Europe 功能描述:VERTICAL FLOAT |
發布緊急采購，3分鐘左右您將得到回復。