- 您現在的位置：買賣IC網 > PDF目錄384884 > RF2689 (RF MICRO DEVICES INC) W-CDMA/GSM/DCS RECEIVE AGC AND DEMODULATOR PDF資料下載
參數資料
| 型號： | RF2689 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | W-CDMA/GSM/DCS RECEIVE AGC AND DEMODULATOR |
| 中文描述： | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC20 |
| 封裝： | 4 X 4 MM, LCC-20 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 383K |
| 代理商： | RF2689 |
Preliminary
7-46
RF2689
Rev A4 010815
7
Q
D
Since the power gain to the input of the Op-Amp G
P
’=
α
G
P
, where G
P
is the power gain of demodulator for matched load.
Therefore, the demodulator power gain is 65+15 = 80 dB.
AC Coupling in Evaluation Board
The output I and Q baseband signal is AC coupled for evaluation purposes only. The high-pass corner frequency is at
1/(2
π
RC)=1/(6.28*30k
*100nF)=56Hz.
I and Q Output DC Voltage and Its Offset
Although the I and Q output is AC coupled on the evaluation board, in most applications, it would be DC coupled to the
ADC input buffer. The DC voltage at the IC output is V
CC
-1.6V with a possible variation of ±0.3V due to temperature and
tolerance. The differential circuit asymmetry would cause common mode DC offset to the extent of ±40mV.
Baseband Filter Calibration Process
The BB (baseband) filter calibration process is same for both WCDMA and GSM/DCS. After calibration is done, the
WCDMA mode sets the circuitry to have a 3dB bandwidth of 2.5MHz, the GSM/DCS mode (if the chip has GSM/DCS
mode) sets the circuitry to have a 3dB bandwidth of 250kHz.
The BB filter in the I and Q path needs to be calculated every time after power down. When the FCLK pin is connected to
a signal generator with 0dBm output level at 13.0MHz, a logic high at CALEN pin for 200
μ
s will calibrate the filter to have
2.5MHz bandwidth with 10% accuracy when WCDMA mode is set, or to 250kHz bandwidth with 10% accuracy when
GSM mode is set. The calibration is done when the chip is powered on only. Calibration is independent from all other
conditions, e.g. the chip enable could be off.
The calibration circuitry consumes 400
μ
A. When the calibration sequence is complete after 200
μ
s, the I
CC
drops to
0mA.
The 3dB bandwidth is defined to be from the reference level at 1MHz for WCDMA and at 50kHz for GSM/DCS. The 3dB
bandwidth is independent of V
GC
and V
CC
.
The filter can also be calibrated with different clock frequencies from 10MHz to 30MHz to tune the bandwidth over -40%
to +60% from its default 3dB bandwidth (2.5MHz for WCDMA and 250kHz for GSM). The 3dB bandwidth is linear with
clock frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| RF2861 | CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER |
| RF2861PCBA-410 | CDMA LOW NOISE AMPLIFIER/MIXER 900MHz DOWNCONVERTER |
| RF2948B | 2.4GHz SPREAD-SPECTRUM TRANSCEIVER |
| RF2948BTR13 | 2.4GHz SPREAD-SPECTRUM TRANSCEIVER |
| RF3100-2 | 3V 900MHZ LINEAR AMPLIFIER MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2689-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V RESETTABLE 2PIN - Tape and Reel |
| RF2690 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:W-CDMA RECEIVE AGC AND DEMODULATOR |
| RF2690-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V RESETTABLE 2PIN - Tape and Reel |
| RF2691-000 | 制造商:TE Connectivity 功能描述:FUSE 40A 72V RESETTABLE - Tape and Reel 制造商:TE Connectivity 功能描述:RXEF250-2 |
| RF2692-000 | 制造商:TE Connectivity 功能描述:RXEF135K-2 - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。