- 您現在的位置：買賣IC網 > PDF目錄374585 > RF2368 (RF MICRO DEVICES INC) DCS/PCS 2.7V LOW NOISE AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2368 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 衰減器 |
| 英文描述： | DCS/PCS 2.7V LOW NOISE AMPLIFIER |
| 中文描述： | 1800 MHz - 2000 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封裝： | SOT, 8 PIN |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 191K |
| 代理商： | RF2368 |
Preliminary
4-202
RF2368
Rev A0 010503
4
G
A
Application Notes
Bypass Mode Configurations
The RF2368 may be placed into either high gain or bypass mode via the GAIN SELECT pin (pin 8). The high gain state
is selected by asserting the GAIN SELECT pin to a voltage level of less than 0.8V. For Bypass operation, there are two
possible methods for placing the RF2368 into this low gain state. The table below shows the two possible Bypass config-
urations.
Bypass Mode Possibilities
Gain Select
2.7
2.7
For both Bypass configurations, the GAIN SELECT pin must be placed at a level greater than or equal to 1.8V. The dif-
ference between the Bypass possibilities is determined by the specific application's ability to change the voltage of the
BIAS pin (pin 1) independently of the V
CC
supply voltage. The advantage of the ability to assert the power down pin to
0V when in Bypass mode is shown by the decreased current draw when in this Bypass configuration.
BIAS Pin Resistor
The BIAS pin (pin1) of the RF2368 should be maintained at 2.7V to 2.86V for proper high gain operation. This voltage
range ensures the correct bias current will be present at the BIAS pin of the device. However, an external series resistor
may be used to allow various operating voltages at this pin (see R1 of the evaluation board schematic). The required
value for this resistor may be roughly calculated by using the operating input voltage to the BIAS pin, the desired voltage
at the device, and the typical current consumption for the BIAS pin, along with Ohm's law.
For example, assume the design will supply 5.0V to the BIAS pin of the device, but the biasing circuitry internal to the
RF2368 requires 2.78V typical, and the BIAS current is known to typically be 0.25mA, then the required value for R1
would be found as follows.
V
0.25
mA
BIAS (V)
0
2.7
VCC1 and VCC2 (V)
2.78
2.78
Current (mA)
1.4
2.2
-------------------------------
8.88
k
=
相關PDF資料 |
PDF描述 |
|---|---|
| RF2368PCBA | DCS/PCS 2.7V LOW NOISE AMPLIFIER |
| RF2369 | 3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
| RF2369PCBA | 3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
| RF2371 | 3V LOW NOISE AMPLIFIER |
| RF2371PCBA | 3V LOW NOISE AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2368PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:DCS/PCS 2.7V LOW NOISE AMPLIFIER |
| RF2369 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
| RF2369_06 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
| RF2369_1 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
| RF2369PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V LOW NOISE AMPLIFIER/ 3V PA DRIVER AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。