- 您現在的位置：買賣IC網 > PDF目錄385767 > RF2175PCBA (RF Micro Devices, Inc.) 3V 400MHZ LINEAR AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2175PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | 3V 400MHZ LINEAR AMPLIFIER |
| 中文描述： | 3V的400MHz的線性放大器 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 109K |
| 代理商： | RF2175PCBA |
Preliminary
2-245
RF2175
Rev A6 010718
2
P
Pin
1
Function
VCC
Description
Power supply for input bias circuitry. A 1nF high frequency bypass
capacitor is recommended.
Interstage Tuning. A shunt inductor to GND is required to optimize the
match.
No connection.
Interface Schematic
2
L TUNE
3
4
NC
Q1C
Power supply for stage 1. V
CC
should be fed through a 25nH or greater
inductor with a decoupling capacitor on the V
CC
side.
Ground for stage 1. For best performance, keep traces physically short
and connect immediately to ground plane. This ground should be iso-
lated from the backside ground contact.
RF input. An external DC blocking capacitor is required if this port is
connected to a DC path to ground or a DC voltage.
No connection.
5
GND1
6
RF IN
7
8
NC
VREG
Power Down control. When this pin is “l(fā)ow”, all circuits are shut off.
When this pin is 2.8V, all circuits are operating normally. V
PD
requires a
regulated 2.8V for the amplifier to operate properly over all specified
temperature and voltage ranges. A dropping resistor from a higher reg-
ulated voltage may be used to provide the required 2.8V. A 100pF high
frequency bypass capacitor is recommended.
No connection.
9
NC
NC
NC
10
11
12
No connection.
No connection.
RF OUT
RF output and power supply for the output stage. The bias for the out-
put stage is provided through this pin and pin 13. An external matching
network is required to provide the optimum load impedance; see the
application schematics for details.
Same as pin 12.
13
14
RF OUT
RF OUT
Harmonic trap. This pin connects to the RF output but is used for pro-
viding a low impedance to the second harmonic of the operating fre-
quency. An inductor or transmission line resonating with a shunt
capacitor at 2f
0
is connected to this pin.
No connection.
15
16
NC
VBIAS
The bias pin allows higher efficiency in low power power modes. When
operating at full output, VBIAS should be 2.8V.
Ground connection. The backside of the package should be soldered to
a top side ground pad, which is connected to the ground plane with
multiple vias. The pad should have a short thermal path to the ground
plane.
Pkg
Base
GND
相關PDF資料 |
PDF描述 |
|---|---|
| RF2175 | 3V 400MHZ LINEAR AMPLIFIER |
| RF2186 | 3V W-CDMA POWER 1900MHZ/ 3V LINEAR POWER AMPLIFIER |
| RF2186PCBA | 3V W-CDMA POWER 1900MHZ/ 3V LINEAR POWER AMPLIFIER |
| RF2189 | 3V, 2.5GHZ LINEAR POWER AMPLIFIER |
| RF2189PCBA | 3V, 2.5GHZ LINEAR POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2177-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2182-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2186 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V W-CDMA POWER 1900MHZ/ 3V LINEAR POWER AMPLIFIER |
| RF2186PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V W-CDMA POWER 1900MHZ/ 3V LINEAR POWER AMPLIFIER |
| RF2187-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。