- 您現在的位置：買賣IC網 > PDF目錄384883 > RF2138PCBA (RF Micro Devices, Inc.) 3V GSM POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2138PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | 3V GSM POWER AMPLIFIER |
| 中文描述： | 3V的的GSM功率放大器 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 145K |
| 代理商： | RF2138PCBA |
2-122
RF2138
Rev A9 011031
2
P
SeeUpgradedProductRF2173
Pin
1
Function
NC
Description
Not connected. Connect this pin to the ground plane for compatibility
with future packages.
Ground connection for the driver stage. To minimize the noise power at
the output, it is recommended to connect this pin with a trace of about
40mil to the ground plane. This will slightly reduce the small signal
gain, and lower the noise power. It is important for stability that this pin
have it’s own vias to the ground plane, minimizing common inductance.
RF Input. This is a 50
input, but the actual impedance depends on the
interstage matching network connected to pin 5. An external DC block-
ing capacitor is required if this port is connected to a DC path to ground
or a DC voltage.
Interface Schematic
2
GND2
See pin 15.
3
RF IN
4
GND1
Ground connection for the pre-amplifier stage. Keep traces physically
short and connect immediately to the ground plane for best perfor-
mance. It is important for stability that this pin has it’s own vias to the
groundplane, to minimize any common inductance.
Power supply for the pre-amplifier stage and interstage matching. This
pin forms the shunt inductance needed for proper tuning of the inter-
stage match. Refer to the application schematic for proper configura-
tion. Note that position and value of the components are important.
Power Control for the driver stage and pre-amplifier. When this pin is
"low," all circuits are shut off. A "low" is typically 0.5V or less at room
temperature. A shunt bypass capacitor is required. During normal oper-
ation this pin is the power control. Control range varies from about 1.0V
for -10dBm to 2.6V for +35dBm RF output power. The maximum power
that can be achieved depends on the actual output matching; see the
application information for more details. The maximum current into this
pin is 5mA when V
APC1
=2.6V, and 0mA when V
APC
=0V.
See pin 3.
5
VCC1
See pin 3.
6
APC1
7
8
9
APC2
VCC
NC
Power Control for the output stage. See pin 6 for more details.
See pin 6.
Power supply for the bias circuits.
See pin 6.
Not connected. Connect this pin to the ground plane for compatibility
with future packages.
RF Output and power supply for the output stage. Bias voltage for the
final stage is provided through this wide output pin. An external match-
ing network is required to provide the optimum load impedance.
10
RF OUT
11
12
13
RF OUT
RF OUT
2F0
Same as pin 10.
Same as pin 10.
Same as pin 10.
Same as pin 10.
Connection for the second harmonic trap. This pin is internally con-
nected to the RF OUT pins. The bonding wire together with an external
capacitor form a series resonator that should be tuned to the second
harmonic frequency in order to increase efficiency and reduce spurious
outputs.
Not connected.
Same as pin 10.
14
15
NC
VCC2
Power supply for the driver stage and interstage matching. This pin
forms the shunt inductance needed for proper tuning of the interstage
match. Please refer to the application schematic for proper configura-
tion, and note that position and value of the components are important.
16
Pkg
Base
VCC2
GND
Same as pin 15.
Same as pin 15.
Ground connection for the output stage. This pad should be connected
to the ground plane by vias directly under the device. A short path is
required to obtain optimum performance, as well as to provide a good
thermal path to the PCB for maximum heat dissipation.
GND1
RF IN
VCC1
From Bias
Stages
GND
VCC
To RF
Stages
GND
APC
GND
PCKG BASE
RF OUT
From Bias
Stages
GND2
VCC2
From Bias
Stages
相關PDF資料 |
PDF描述 |
|---|---|
| RF2138 | 3V GSM POWER AMPLIFIER |
| RF2140 | 3V DCS POWER AMPLIFIER |
| RF2140PCBA | 3V DCS POWER AMPLIFIER |
| RF2145 | DCS1800/1900 POWER AMPLIFIER |
| RF2145PCBA | DCS1800/1900 POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2139-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2140 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V DCS POWER AMPLIFIER |
| RF2140-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2140PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V DCS POWER AMPLIFIER |
| RF2141-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。