- 您現在的位置：買賣IC網 > PDF目錄385767 > RF2117PCBA (RF Micro Devices, Inc.) HIGH EFFICIENCY 400MHZ AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2117PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | HIGH EFFICIENCY 400MHZ AMPLIFIER |
| 中文描述： | 400MHz的高效率放大器 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 173K |
| 代理商： | RF2117PCBA |
Preliminary
2-49
RF2117
Rev A0 991201
2
P
Pin
1
Function
VREG
Description
Regulated Supply for bias circuit. This pin should be connected to the
regulated supply with a ferrite of 240 ohms and should have a UHF
decoupling capacitor (100pF) to ground at the supply end of the ferrite.
An additional capacitor of 1nF can be added with the 100 pF but it’s
placement is not as critical.
Positive supply for the active bias circuits. Bypassing should be accom-
plished with a single UHF decoupling capacitor, placed close to the Pin.
Additional bypassing of 1nF is also recommended, but proximity to the
package is not as critical.
The Inter-stage matching point of the amplifiers. Matching should be
performed with a small value inductor connected from the pin to
ground.
Positive Supply to the first stage collector. The supply should be fed
through a parallel LC network, resonant at the centre of the band of
interest. A UHF decoupling capacitor should be placed from the supply
end of the LC to ground. A 1nF capacitor can also be used but it’s
placement it not as critical.
Ground Contact for the driver stage. Keep traces physically short and
connect immediately to the ground plane for best performance. It is
important for stability that this pin has it’s own via to the groundplane, to
minimize any common inductance.
Amplifier RF input. This is a 50
RF input port to the amplifier. It does
not contain internal DC blocking and therefore should be externally DC
blocked before connecting to any device which has DC present or
which contains a DC path to ground. A series UHF capacitor is recom-
mended for the DC blocking.
Not internally connected.
Interface Schematic
2
VCC1
3
LTUNE
4
Q1C
5
GND
6
RF IN
7
8
NC
VPD
Power Down control. When this pin is “l(fā)ow” all circuits are off. A low is
typically less than 0.5V at room temperature. This pin affords a mea-
sure of power control, however this response is not linear across much
of the range. It is recommended that the pin be used in closed loop
power control systems if it is to be used across a range of voltages and
temperatures for power control.
Not internally connected.
9
NC
NC
NC
10
11
12
Not internally connected.
Not internally connected.
RF OUT
Amplifier RF output. This is an unmatched collector output of the final
amplifier transistor. It is internally connected to pins 12, 13, and 14 to
provide low series inductance and flexibility in output matching. Bias for
the final power amplifier output transistor must also be provided
through two of these three pins. Typically, these pins are externally con-
nected very close to the package and used as the RF output with a
matching network that presents the optimum load impedance to the PA
for maximum power and efficiency, as well as providing DC blocking at
the output. An additional network of a bias inductor (or
λ
/4 line) pro-
vides DC bias and helps to protect the output from high voltage swings
due to severe load mismatches.
Amplifier RF output, same as pin 12
13
14
RF OUT
RF OUT
Amplifier RF output, same as pin 12. Do not feed the supply to this pin
alone. If this pin is used as the supply pin it must be connected in paral-
lel with pin 12 and/or 13.
Not internally connected.
15
16
Pkg
Base
NC
NC
GND
Not internally connected.
This contact is the main ground contact for the entire device. Care
should be taken to ensure that this contact is well soldered in order to
prevent performance from being degraded from that indicated in the
specifications.
相關PDF資料 |
PDF描述 |
|---|---|
| RF2119 | HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2119PCBA | HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2125P | HIGH POWER LINEAR AMPLIFIER |
| RF2125PPCBA | HIGH POWER LINEAR AMPLIFIER |
| RF2125 | HIGH POWER LINEAR AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2118-000 | 制造商:TE Connectivity 功能描述:MICROSMD250LR-A-2 - Tape and Reel 制造商:TE Connectivity 功能描述:POLYSWITCH RESETTABLE DEVICE SMD 制造商:TE Connectivity / Raychem 功能描述:POLYSWITCH RESETTABLE DEVICE SMD |
| RF2119 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2119-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2119PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF212 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Image-Reject Front End for Dual or Tri-Band GSM Applications |
發布緊急采購，3分鐘左右您將得到回復。