- 您現在的位置：買賣IC網 > PDF目錄385767 > RF2115LPCBA (RF Micro Devices, Inc.) HIGH POWER UHF AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2115LPCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | HIGH POWER UHF AMPLIFIER |
| 中文描述： | 大功率高頻放大器 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 101K |
| 代理商： | RF2115LPCBA |
2-41
RF2115L
Rev B1 010329
2
P
SeeUpgradedProductRF2117
NC
Pin
1
Function
VCC2
Description
Positive supply for the second stage (driver) amplifier. This is an
unmatched transistor collector output. This pin should see an inductive
path to AC ground (V
CC
with a UHF bypassing capacitor). This induc-
tance can be achieved with a short, thin microstrip line or with a low
value chip inductor (approximately 2.7nH). At lower frequencies, the
inductance value should be larger (longer microstrip line) and V
CC
should be bypassed with a larger bypass capacitor (see the application
schematic for 430MHz operation). This inductance forms a matching
network with the internal series capacitor between the second and third
stages, setting the amplifier’s frequency of maximum gain. An addi-
tional 1
μ
F bypass capacitor in parallel with the UHF bypass capacitor is
also recommended, but placement of this component is not as critical.
In most applications, pins 1, 2, and 3 can share a single 1
μ
F bypass
capacitor.
Positive supply for the active bias circuits. This pin can be externally
combined with pin 3 (VCC1) and the pair bypassed with a single UHF
capacitor, placed as close as possible to the package. Additional
bypassing of 1
μ
F is also recommended, but proximity to the package is
not as critical. In most applications, pins 1, 2, and 3 can share a single
1
μ
F bypass capacitor.
Positive supply for the first stage (input) amplifier. This pin can be exter-
nally combined with pin 2 (VCC3) and the pair bypassed with a single
UHF capacitor, placed as close as possible to the package. Additional
bypassing of 1
μ
F is also recommended, but proximity to the package is
not as critical. In most applications, pins 1, 2, and 3 can share a single
μ
F bypass capacitor. This pin can also be used for coarse analog gain
control, even though it is not optimized for this function.
Ground connection. Keep traces physically short and connect immedi-
ately to ground plane for best performance. In addition, for specified
performance, the package’s backside metal should be soldered to
ground plane.
Power down control voltage. When this pin is at 0V, the device will be in
power down mode, dissipating minimum DC power. When this pin is at
5V the device will be in full power mode delivering maximum available
gain and output power capability. This pin may also be used to perform
some degree of gain control or power control when set to voltages
between 0V and 5V. It is not optimized for this function so the transfer
function is not linear over a wide range as with other devices specifi-
cally designed for analog gain control; however, it may be usable for
coarse adjustment or in some closed loop AGC systems. This pin
should not, in any circumstance, be higher in voltage than V
CC
, nor
should it ever be higher than 6.5V. This pin should also have an exter-
nal UHF bypassing capacitor.
Amplifier RF input. This is a 50
RF input port to the amplifier. It does
not contain internal DC blocking and therefore should be externally DC
blocked before connecting to any device which has DC present or
which contains a DC path to ground. A series UHF capacitor is recom-
mended for the DC blocking.
RF output power gain control MSB (see specification table for logic).
The control voltage at this pin should never exceed V
CC
. This pin
should also have an external UHF bypassing capacitor.
RF output power gain control LSB (see specification table for logic).
The control voltage at this pin should never exceed V
CC
. This pin
should also have an external UHF bypassing capacitor.
Not internally connected.
Interface Schematic
2
VCC3
3
VCC1
4
GND
5
PD
6
RF IN
7
G20
8
G10
9
相關PDF資料 |
PDF描述 |
|---|---|
| RF2117 | HIGH EFFICIENCY 400MHZ AMPLIFIER |
| RF2117PCBA | HIGH EFFICIENCY 400MHZ AMPLIFIER |
| RF2119 | HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2119PCBA | HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2125P | HIGH POWER LINEAR AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2117 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:HIGH EFFICIENCY 400MHZ AMPLIFIER |
| RF2117PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:HIGH EFFICIENCY 400MHZ AMPLIFIER |
| RF2118-000 | 制造商:TE Connectivity 功能描述:MICROSMD250LR-A-2 - Tape and Reel 制造商:TE Connectivity 功能描述:POLYSWITCH RESETTABLE DEVICE SMD 制造商:TE Connectivity / Raychem 功能描述:POLYSWITCH RESETTABLE DEVICE SMD |
| RF2119 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:HIGH EFFICIENCY 2V POWER AMPLIFIER |
| RF2119-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。