- 您現在的位置：買賣IC網 > PDF目錄385767 > RF-3000PCBA (RF Micro Devices, Inc.) SPREAD-SPECTRUM BASEBAND MODEM PDF資料下載
參數資料
| 型號： | RF-3000PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | SPREAD-SPECTRUM BASEBAND MODEM |
| 中文描述： | 擴譜基帶調制解調器 |
| 文件頁數： | 15/28頁 |
| 文件大小： | 351K |
| 代理商： | RF-3000PCBA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
11-335
RF3000
Rev A4 031216
Another optional mode has been added to the AGC algorithm. This mode adds a delay into the algorithm after the LNA
gain select is changed to allow enough time for the radio to settle properly. The delay eliminates the possibility of a 'dead
zone' where there is a small range of input power levels with a probability that the AGC will settle to an incorrect gain set-
ting. To enable this mode, Register 0x1D is written to 0x80. In addition, the 6 lsb's of reg20 must be set to 4 higher the 6
lsb's of reg21 because the outcome of the AGC decision step will change. If this mode is not to be used, Register 0x1D
should be written to 0x00.
AGC Calibration
The RF3000 is preprogrammed for a “typical” radio. The default settings of the RF3000 may be used without modifica-
tion, but the conditions of the AGC algorithm may be modified by writing to register 21 and register 20 of the control port.
Register 21 controls an offset to the RXVGC DAC for LNAGS=1 (high gain mode), and register 20 controls an offset to
the RXVGC DAC for LNAGS=0 (low gain mode). Caution should be taken when setting these registers; incorrect set-
tings can create a “dead zone” between the high/low gain trees. The following figure shows the “typical” settings for the
RXVGC output of the RF3000 during LNAGS=1. Also shown are the expected production variances of an IEEE802.11
radio, and the calibration ranges of the RF3000. Writing to register 21 of the RF3000 will move the range of AGC opera-
tion on the RXVGC pin. For example, if the six LSB's in register 21 are written to 000100b (4 decimal), the starting point
for the AGC algorithm (max gain) will be with a DAC code of 8+4=12 codes, and the LNAGS decision will be made at a
code of 47+4=51 codes. This has the overall effect of decreasing the gain provided by the RF2948 by four D/A codes or
approximately 5dB for both initial AGC setting for detection of saturation and for determining LNAGS. Likewise if the six
LSB's of register 21 are written to 1111000 (-4 decimal), the initial condition that the RF3000 uses to look for saturation
is 8-4=4 codes, and the LNAGS decision is determined at 47-4=43 codes.
Similar to the high gain calibration, register 20 controls an offset into the LNAGS=0 (low gain mode) values that are
applied to the D/A converter. The figure below shows the normal operation range of the RF3000 and the calibration
range that is provided.
Cal Range
Cal Range
Typical RF3000 AGC Range
0
63
8
24
39
47
D/A Code
Typical
RF2948
Gain
67.8dB
21.7dB
Process
Variation
Process
Variation
Figure 11. High Gain Mode (LNAGS=1) Plot of RXVGC Showing Normal Operation and Calibration Ranges
Cal Range
Cal Range
Typical RF3000 AGC Range
0
63
8
17
39
54
D/A Code
Typical
RF2948
Gain
67.8dB
13.4dB
Process
Variation
Process
Variation
Figure 12. Low Gain Mode (LNAGS=0) Plot of RXVGC Showing Normal Operation and Calibration Ranges
相關PDF資料 |
PDF描述 |
|---|---|
| RF3000 | SPREAD-SPECTRUM BASEBAND MODEM |
| RF3000PCBA | SPREAD-SPECTRUM BASEBAND MODEM |
| RF2046PCBA-41X | GENERAL PURPOSE AMPLIFIER |
| RF2114 | TRI R RECP F FLG SEAL 0-4 |
| RF2114PCBA | MEDIUM POWER LINEAR AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF300-12 | 功能描述:高頻/射頻繼電器 12V DC-6GHz .15W RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz |
| RF300-12/G | 制造商:Teledyne Relays 功能描述:RF RELAY |
| RF3001A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FUELLSTANDSFUEHLER VERT |
| RF-3001A | 制造商:Assemtech 功能描述:VERTICAL FLOAT 制造商:Comus Europe 功能描述:VERTICAL FLOAT |
| RF3001A/VFS30 | 制造商:ASSEMTECH 功能描述:FLOAT SWITCH VERT 制造商:ASSEMTECH 功能描述:FLOAT SWITCH, VERT 制造商:ASSEMTECH 功能描述:FLOAT SWITCH, VERT; Output Current:500mA; Operating Pressure Max:10bar; Sensor Body Material:Stainless Steel; SVHC:No SVHC (19-Dec-2012); Body Material:Stainless Steel; Contact Configuration:SPST; Contact Current AC Max:1A; Contact |
發布緊急采購，3分鐘左右您將得到回復。