參數資料
型號： RF-3000
廠商： RF Micro Devices, Inc.
英文描述： SPREAD-SPECTRUM BASEBAND MODEM
中文描述： 擴譜基帶調制解調器
文件頁數： 9/28頁
文件大?。?/td> 351K
代理商： RF-3000
11-329
RF3000
Rev A4 031216
SPI Control Port
The control port is used by the Media Access Controller (MAC) to set up and modify the multiple operation modes of the
RF3000. The port is set to SPI mode, with the RF3000 acting as Slave. Note that if no setup information is programmed
into the RF3000's registers, it will default to a BPSK 1Mbps IEEE802.11b DSSS mode. If an IEEE802.11b mode is
selected in Register 1, other waveform registers are ignored and the appropriate, standards compliant features are
enabled (e.g., PN code, preamble/header, etc.). TX length is required for all IEEE802.11b modes.
All Registers, as defined in the Register Definition section of this datasheet, can be read in real time through this control
port. Selected registers, as indicated in the Register section are read-only.
The control port of the RF3000 contains a mode to automatically increment the register pointer, allowing reading or writ-
ing of adjacent bytes without the need to stop and restart control port access.
SPI Mode Description
SPI mode pin definitions.
SPI Method of Operation
Write:
To Write into a register of the RF3000, the accessing SPI master needs to simply bring CS low, then Address the
RF3000 (0100000
2
) and provide a '0' for the Read/Write-bit. The user should note that all data transfers to/from the
RF3000 are msb first. This should be followed by the Auto-increment-bit and the Memory address pointer (MAP), this is
an 7-bit value to indicate the initial address for the write process. Register data is to immediately follow the MAP. If the
Auto-Increment-bit is set RF3000 will continue to write data 1 byte at a time into the address pointed to by the MAP, and
increment the MAP after each byte. When the SPI Master is finished filling registers, it must raise CS to indicate the cycle
end.
Read:
Reading the contents of the RF3000 internal registers, the procedure is actually a write process followed by the read.
The SPI Master must bring CS low, to prepare the RF3000 to look for its address. The SPI Master now addresses the
RF3000, by placing the RF3000 base address (0100000
2
) on the data bus and append a '0' for the Read/Write-bit. The
SPI Master must now set the Auto-increment-bit and initialize the 7-bit MAP to the value of the register to be read. The
user should raise CS, to end the write portion of the cycle. To complete the Write/Read cycle the SPI Master now needs
to lower CS again, and readdress the RF3000 providing a '1' for the Read/Write-bit. Once this is completed the RF3000
will begin outputting the register contents. As long as the CS remains low, and the auto-increment bit is set, the RF3000
will auto-increment the MAP. When the RF3000 reaches Address 31, the MAP will be reset to Register 0 and the process
continues.
Pin Name
Description
CS
Serial port chip select. A value of '0' is port enabled.
C CLK
Control port-bit clock input from serial port master.
CD IN
Serial data input to the RF3000. Data is clocked in on the rising edge of C CLK.
CD OUT
Serial data output from the RF3000. Data is clocked out on the falling edge of C CLK.
相關PDF資料
PDF描述
RF-3000PCBA SPREAD-SPECTRUM BASEBAND MODEM
RF3000 SPREAD-SPECTRUM BASEBAND MODEM
RF3000PCBA SPREAD-SPECTRUM BASEBAND MODEM
RF2046PCBA-41X GENERAL PURPOSE AMPLIFIER
RF2114 TRI R RECP F FLG SEAL 0-4
相關代理商/技術參數
參數描述
RF3000PCBA 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM
RF-3000PCBA 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:SPREAD-SPECTRUM BASEBAND MODEM
RF300-12 功能描述:高頻/射頻繼電器 12V DC-6GHz .15W RoHS:否 制造商:Omron Electronics 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 VDC 線圈類型:Non-Latching 頻率: 功耗:100 mW 端接類型:Solder Terminal 絕緣:20 dB to 30 dB at 1 GHz 介入損耗:0.2 dB at 1 GHz
RF300-12/G 制造商:Teledyne Relays 功能描述:RF RELAY
RF3001A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FUELLSTANDSFUEHLER VERT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*