參數資料
型號： REF198GSZ
廠商： ANALOG DEVICES INC
元件分類： 基準電壓源/電流源
英文描述： Precision Micropower, Low Dropout Voltage References
中文描述： 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 4.096 V, PDSO8
封裝： ROHS COMPLIANT, MS-012AA, SOIC-8
文件頁數： 19/28頁
文件大?。?/td> 407K
代理商： REF198GSZ
REF19x Series
APPLICATIONS
OUTPUT SHORT-CIRCUIT BEHAVIOR
The REF19x family of devices is completely protected from
damage due to accidental output shorts to GND or to V
+
. In the
event of an accidental short-circuit condition, the reference
device shuts down and limits its supply current to 40 mA.
Rev. I | Page 19 of 28
V
+
V
OUT
SLEEP (SHUTDOWN)
GND
0
Figure 20. Simplified Schematic
DEVICE POWER DISSIPATION CONSIDERATIONS
The REF19x family of references is capable of delivering load
currents to 30 mA with an input voltage that ranges from
3.3 V to 5 V. When these devices are used in applications with
large input voltages, exercise care to avoid exceeding the
maximum internal power dissipation of these devices.
Exceeding the published specifications for maximum power
dissipation or junction temperature can result in premature
device failure. The following formula should be used to
calculate a device’s maximum junction temperature or
dissipation:
T
T
P
θ
JA
A
J
D
=
In this equation, T
J
and T
A
are the junction and ambient
temperatures, respectively; P
D
is the device power dissipation;
and θ
JA
is the device package thermal resistance.
OUTPUT VOLTAGE BYPASSING
For stable operation, low dropout voltage regulators and
references generally require a bypass capacitor connected from
their V
OUT
pins to their GND pins. Although the REF19x family
of references is capable of stable operation with capacitive loads
exceeding 100 μF, a 1 μF capacitor is sufficient to guarantee
rated performance. The addition of a 0.1 μF ceramic capacitor
in parallel with the bypass capacitor improves load current
transient performance. For best line voltage transient
performance, it is recommended that the voltage inputs of these
devices be bypassed with a 10 μF electrolytic capacitor in
parallel with a 0.1 μF ceramic capacitor.
SLEEP MODE OPERATION
All REF19x devices include a sleep capability that is
TTL/CMOS-level compatible. Internally, a pull-up current
source to V
IN
is connected at the SLEEP pin. This permits the
SLEEP pin to be driven from an open collector/drain driver. A
logic low or a 0 V condition on the SLEEP pin is required to
turn off the output stage. During sleep, the output of the
references becomes a high impedance state where its potential
would then be determined by external circuitry. If the sleep
feature is not used, it is recommended that the SLEEP pin be
connected to V
IN
(Pin 2).
BASIC VOLTAGE REFERENCE CONNECTIONS
The circuit in Figure 21 illustrates the basic configuration for
the REF19x family of references. Note the 10 μF/0.1 μF bypass
network on the input and the 1 μF/0.1 μF bypass network on
the output. It is recommended that no connections be made to
Pin 1, Pin 5, Pin 7, and Pin 8. If the sleep feature is not required,
Pin 3 should be connected to V
IN
.
NC
NC
OUTPUT
V
IN
SLEEP
NC
NC
0.1μF
10μF
REF19x
NC = NO CONNECT
8
7
6
5
1
2
3
4
1μF
TANT
0.1μF
+
0
Figure 21. Basic Voltage Reference Configuration
MEMBRANE SWITCH-CONTROLLED POWER
SUPPLY
With output load currents in the tens of mA, the REF19x family
of references can operate as a low dropout power supply in
hand-held instrument applications. In the circuit shown in
Figure 22, a membrane on/off switch is used to control the
operation of the reference. During an initial power-on condition,
the SLEEP pin is held to GND by the 10 kΩ resistor. Recall that
this condition (read: three-state) disables the REF19x output.
When the membrane on switch is pressed, the SLEEP pin is
momentarily pulled to V
IN
, enabling the REF19x output. At this
point, current through the 10 kΩ resistor is reduced, and the
internal current source connected to the SLEEP pin takes
control. Pin 3 assumes and remains at the same potential as V
IN
.
When the membrane off switch is pressed, the SLEEP pin is
momentarily connected to GND, which once again disables the
REF19x output.
相關PDF資料
PDF描述
REF198GSZ-REEL Precision Micropower, Low Dropout Voltage References
REF194GSZ Precision Micropower, Low Dropout Voltage References
REF194GSZ-REEL Precision Micropower, Low Dropout Voltage References
REF194GSZ-REEL7 Precision Micropower, Low Dropout Voltage References
REF195ES-REEL Precision Micropower, Low Dropout Voltage References
相關代理商/技術參數
參數描述
REF198GSZ 制造商:Analog Devices 功能描述:Voltage Reference
REF198GSZ-REEL 功能描述:IC VREF SERIES PREC 4.096V 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:REF19 產品培訓模塊:Voltage Reference Basics 標準包裝:100 系列:- 基準類型:旁路，精度 輸出電壓:4.096V 容差:±0.075% 溫度系數:50ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:1µA 電流 - 靜態:- 電流 - 輸出:10mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:管件
REF19X 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Micropower, Low Dropout Voltage References
REF19XES 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Micropower, Low Dropout, Voltage References
REF19XES3 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Micropower, Low Dropout Voltage References
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*