- 您現在的位置：買賣IC網 > PDF目錄368446 > RC5041M (Raytheon Company) Programmable DC-DC Converter for Pentium P55C, K6 and 6x86MX (M2) Processors PDF資料下載
參數資料
| 型號： | RC5041M |
| 廠商： | Raytheon Company |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Programmable DC-DC Converter for Pentium P55C, K6 and 6x86MX (M2) Processors |
| 中文描述： | 可編程DC - DC轉換為奔騰P55C，K6和6x86MX量（M2）處理器 |
| 文件頁數： | 14/16頁 |
| 文件大小： | 119K |
| 代理商： | RC5041M |
RC5041
PRODUCT SPECIFICATION
14
P
PCB Layout Guidelines and
Considerations
PCB Layout Guidelines
Placement of the MOSFETs relative to the RC5041 is
critical. The MOSFETs (M1 & M2), should be placed
such that the trace length of the HIDRV pin from the
RC5041 to the FET gates is minimized. A long lead length
on this pin will cause high amounts of ringing due to the
inductance of the trace combined with the large gate
capacitance of the FET. This noise will radiate all over the
board, and because it is switching at such a high voltage
and frequency, it will be very difficult to suppress.
The drawing below depicts an example of good placement
for the MOSFETs in relation to the RC5041
and also an example of problematic placement for the
MOSFETs.
In general, all of the noisy switching lines should be kept
away from the quiet analog section of the RC5041. That is
to say, traces that connect to pins 8 and 9 (HIDRV and
VCCQP) should be kept far away from the traces that
connect to pins 1 through 4, and pin 12.
Place decoupling capacitors (.1
μ
F) as close to the RC5041
pins as possible. Extra lead length on these will negate
their ability to suppress noise.
Each VCC and GND pin should have its own via down to
the appropriate plane underneath. This will help give
isolation between pins.
Surround the CEXT timing capacitor with a ground trace
as much as possible. Also be sure to keep a ground or
power plane underneath the capacitor for further noise
isolation. This will help to shield the oscillator pin 1 from
the noise on the PCB. Place this capacitor as close to the
RC5041 pin 1 as possible.
Place MOSFETs, inductor and Schottky as close together
as possible for the same reasons as #1 above. Place the
input bulk capacitors as close to the drains of MOSFETs
as possible. In addition, placement of a 0.1
μ
F decoupling
cap right on the drain of each MOSFET will help to
suppress some of the high frequency switching noise on
the input of the DC-DC converter.
The traces that run from the RC5041 IFB (pin 3) and VFB
(pin 4) pins should be run together next to each other and
be Kelvin connected to the sense resistor. Running these
lines together will help in rejecting some of the common
noise that is presented to the RC5041 feedback input. Try
as much as possible to run the noisy switching signals
(HIDRV & VCCQP) on one layer; and use the inner layers
for only power and ground. If the top layer is being used to
route all of the noisy switching signals, use the bottom
layer to route the analog sensing signals VFB and IFB.
Figure 10. MOSFET Layout Guidelines
Correct layout
8
7
6
2
M1
M2
M1
M2
10
11
9
3
12
1
5
4
Poor layout
“Quiet" Pins
=
13
14
15
16
8
7
6
2
10
11
9
3
12
1
5
4
13
14
15
16
65-5041-12
相關PDF資料 |
PDF描述 |
|---|---|
| RC5042 | Programmable DC-DC Converter |
| RC5042M | Programmable DC-DC Converter |
| RCH-110 | Radial Leaded Inductors |
| RCH-654 | Radial Leaded Inductors |
| RCH-664 | Radial Leaded Inductors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RC5042 | 制造商:RAYTHEON 制造商全稱:RAYTHEON 功能描述:Programmable DC-DC Converter |
| RC5042M | 制造商:RAYTHEON 制造商全稱:RAYTHEON 功能描述:Programmable DC-DC Converter |
| RC5042MT | 制造商:RAYTHEON 功能描述:* |
| RC5043 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RC5043M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller |
發布緊急采購，3分鐘左右您將得到回復。