參數資料
型號： QT60168-ASG
廠商： Atmel
文件頁數： 24/28頁
文件大小： 0K
描述： IC SENSOR QMATRIX 16CHAN 32TQFP
標準包裝： 250
系列： QMatrix™, QProx™
類型： 電容性
輸入數/鍵： 16 鍵
分辨率（位）： 9，11 b
評估套件： 可供
數據接口： 串行，SPI?
電源電壓： 3 V ~ 5 V
電流 - 電源： 25mA
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 32-TQFP
供應商設備封裝： 32-TQFP（7x7）
包裝： 托盤
產品目錄頁面： 2822 (CN2011-ZH PDF)
配用： 427-1087-ND - BOARD EVAL QT60248-AS QMATRIX
其它名稱： 427-1107
Increasing the burst length (BL) parameter will increase the
signal strengths as will increasing the sampling resistor (Rs)
values.
2.8 Matrix Series Resistors
The X and Y matrix scan lines should use series resistors
(referred to as Rx and Ry respectively) for improved EMI
performance.
X drive lines require them in most cases to reduce edge rates
and thus reduce RF emissions. Typical values range from 1K to
20K ohms.
Y lines need them to reduce EMC susceptibility problems and in
some extreme cases, ESD. Typical Y values range around 1K
ohms. Y resistors act to reduce noise susceptibility problems by
forming a natural low-pass filter with the Cs capacitors.
It is essential that the Rx and Ry resistors and Cs capacitors be
placed very close to the chip. Placing these parts more than a
few millimeters away opens the circuit up for high frequency
interference problems (above 20MHz) as the trace lengths
between the components and the chip start to act as RF
antennae.
The upper limits of Rx and Ry are reached when the signal
level and hence key sensitivity are clearly reduced. The limits of
Rx and Ry will depending on key geometry and stray
capacitance, and thus an oscilloscope is required to determine
optimum values of both.
The upper limit of Rx can vary depending on key geometry and
stray capacitance, and some experimentation and an
oscilloscope are required to determine optimum values.
Dwell time is the duration in which charge coupled from X to Y
is captured. Increasing Rx values will cause the leading edge of
the X pulses to increasingly roll off, causing the loss of captured
charge (and hence loss of signal strength) from the keys
(Figure 2-4). The dwell time of these parts is fixed at 375ns. If
the X pulses have not settled within 375ns, key gain will be
reduced; if this happens, either the stray capacitance on the X
line(s) should be reduced (by a layout change, for example by
reducing X line exposure to nearby ground planes or traces), or,
the Rx resistor needs to be reduced in value (or a combination
of both approaches).
One way to determine X line settling time is to monitor the fields
using a patch of metal foil or a small coin over the key (Figure
2-5). Only one key along a particular X line needs to be
observed, as each of the keys along that X line will be identical.
The 250ns dwell time should be exceed the observed 95%
settling of the X-pulse by 25% or more.
In almost all case, Ry should be set equal to Rx, which will
ensure that the charge on the Y line is fully captured into the Cs
capacitor.
2.9 Key Design
Circuits can be constructed out of a variety of materials
including flex circuits, FR4, and even inexpensive single-sided
CEM-1.
The actual internal pattern style is not as important as is the
need to achieve regular X and Y widths and spacings of
sufficient size to cover the desired graphical key area or a little
bit more; ~3mm oversize is acceptable in most cases, since the
key’s electric fields drop off near the edges anyway. The overall
key size can range from 10mm x 10mm up to 100mm x 100mm
but these are not hard limits. The keys can be any shape
including round, rectangular, square, etc. The internal pattern
lQ
5
QT60248-AS R4.02/0405
Figure 2-4 X-Drive Pulse Roll-off and Dwell Time
Figure 2-5 Probing X-Drive Waveforms With a Coin
X drive
Lost charge due to
inadequate settling
before end of dwell time
Y gate
Dwell time
Figure 2-6 Recommended Key Structure
‘T’ should ideally be similar to the complete thickness the fields need to
penetrate to the touch surface. Smaller dimensions will also work but will give
less signal strength. If in doubt, make the pattern coarser.
相關PDF資料
PDF描述
SY100EL16VBZC TR IC RCVR DIFF 5V/3.3V 8-SOIC
MS27472E24A29P CONN RCPT 29POS WALL MT W/PINS
SY100EL16VBZC IC RCVR DIFF 5V/3.3V 8-SOIC
AD7877ACPZ-500RL7 IC ADC 12BIT TOUCHSCREEN 32LFCSP
D38999/20WJ29PD CONN RCPT 29POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
QT60168-ASG QS656 制造商:Atmel Corporation 功能描述:Q Matrix IC 32-Pin TQFP 制造商:Atmel 功能描述:Q Matrix IC 32-Pin TQFP
QT60168-ASG SL683 制造商:Atmel Corporation 功能描述:
QT60168-ASG-SL683 功能描述:接口 - 專用 Integrated Circuit RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
QT60168C-ASG 功能描述:接口 - 專用 Integrated Circuit RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
QT60168C-ASG-SL683 功能描述:接口 - 專用 Integrated Circuit RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*