- 您現在的位置：買賣IC網 > PDF目錄2016 > QPO-1LZ-01 (Vicor Corporation)IC INTERFACE FILTER PDF資料下載
參數資料
| 型號： | QPO-1LZ-01 |
| 廠商： | Vicor Corporation |
| 文件頁數： | 14/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE FILTER |
| 標準包裝： | 20 |
| 系列： | Picor®, QUIETPOWER® |
| 其它名稱： | 1102-1095-5 |
PICOR Corporation picorpower.com
QPO-1
Rev 3.6
Page 6 of 17
QPO-1
QUIETPOWER
a current into the converter’s SC/Trim pin to raise the output
voltage of the converter.
The current required to increase a converter’s output voltage
is dependent on the converter and its internal reference
circuitry. The QPO-1 is designed to drive a converter which
has a fixed reference voltage with a series resistor which can
be offset by the injection of current into the pin. The current
can be calculated using the following equation:
Where; VOUT = Nominal converter output voltage
VRPT = internal reference voltage
VHR = QPO-1’s headroom voltage.
RIN = internal series resistor.
The RSCSET resistor is calculated by dividing the headroom
voltage by ISCSET.
The RSCSET equation reduces to the
following:
Where; VOUT = Nominal converter output voltage
VRPT = internal reference voltage
RIN = internal series resistor.
When using one of Vicor’s Micro, Mini or Maxi converters, the
RIN = 1kΩ and the VRPT = 1.23V.
The RSL resistor, shown in Figure 3, is used to limit the
amount of current the QPO-1 can source during start-up. The
SC current is derived from the headroom voltage and at start-
up the headroom voltage is greater than when in normal
operation. This higher current can over-drive a converter to
the point where an over-voltage fault can occur. RSL is
calculated using the following equation:
Where; RSL = current limiting resistor for the QPO SC circuit,
VIN = the QPO’s input voltage,
VRPT = the nominal SC voltage of the converter,
ISCMAX = the current that will force a converter to
have 110% of its nominal voltage on its
output.
Where; ISCMAX = the current that will force a converter to
have 110% of its nominal voltage on its
output.
VSC = the nominal SC voltage of the converter,
RINT = the internal series resistor of the converter’s
reference circuit.
Remote Sense:
Compensation for the QPO-1’s voltage drop can be done
using the converter’s remote sense pins, if available. The on-
board sensing network can be attached as is shown in Figure
10, using RRS and CRS.
相關PDF資料 |
PDF描述 |
|---|---|
| QPO-2LZ-01 | IC INTERFACE FILTER |
| QPO-2LZ | 0.3-5.5V 20A OUT RIP ATTENUATOR |
| RX-4801JE:UB | IC REAL TIME CLOCK MODULE |
| RX-5412SF: B3 PURE SN | IC REAL TIME CLOCK 24-SOP |
| RX-8801SA:UB3 PURE SN | IC REAL TIME CLOCK 14-SOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPO-1Q | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Output Ripple Attenuation SiP |
| QPO-2EVAL1 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Evaluation Board for QPO-2 Active Output Filter |
| QPO-2-EVAL1 | 功能描述:EVALUATION BOARD FOR QPO-2 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Picor®, QUIETPOWER® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| QPO-2L | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:OUTPUT RIPPLE ATTENUATOR |
| QPO-2LZ | 功能描述:0.3-5.5V 20A OUT RIP ATTENUATOR RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。