- 您現在的位置：買賣IC網 > PDF目錄299801 > QPI-3-EVAL1 (Vicor Corporation) Evaluation Board for Active EMI Filters PDF資料下載
參數資料
| 型號： | QPI-3-EVAL1 |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Evaluation Board for Active EMI Filters |
| 中文描述： | 評估板有源EMI濾波器 |
| 文件頁數： | 1/2頁 |
| 文件大?。?/td> | 126K |
| 代理商： | QPI-3-EVAL1 |
Picor Corporation www.picorpower.com
QPI-X-EVAL1 Data Sheet Rev. 1.2 Page 1 of 2
The QPI-X-EVAL1 is an easy to use evaluation
board for testing the QPI family of active EMI
filters. The evaluation board includes a mounted
QPI, capacitors, optional RY resistor and screw
terminals for electrical connections.
When using the evaluation board, pay special
attention to wiring and grounding. Wires should be
kept as short as possible and positioned to minimize
radiated pick up around the QPI. Refer to Figure 1
below and the QPI-AN1 application note for the
proper measurement set up.
Figure 2 shows the schematic of the QPI-X-EVAL1.
Note that resistor RY is included with the evaluation
board for use with non-resonant mode converters. To
ensure the best results, make sure that the QPI shield
connection is as close as possible to the common point
of the bypass Y-capacitors and shield plane under the
converters on the system board.
BUS+
QPI+
BUS-
QPI-
SHIELD
BUS
SUPPLY
QPI
VIN+
VOUT+
VIN-
VOUT-
CONVERTER
Optional GND
Connection
C1
C2
C3
C4
RY
CIN
LISN
LISN Ground Plane
Figure 1 - Spectrum Analyzer Test Setup for the evaluation board (QPI and Converter 5mm above LISN Ground Plane)
Figure 3 shows the component locations on the EVAL
board PCB.
Filter performance in the application is highly
dependent on several factors and cannot be
extrapolated from insertion loss curves alone. Final
noise performance is a complex function of filter
elements, equipment grounding and noise source
impedances, which vary in magnitude and phase over
the frequency spectrum of interest.
Designers should be aware that to select and qualify
an EMI filter for conducted noise, they must test the
filter in their product under the set up and conditions
specified in the applicable EMI standards. Measurements
should be made in consultation with in-house
compliance testing or an independent EMI test facility.
Check www.picorpower.com for data sheets,
application notes and additional product information.
QPI-X-EVAL1
QuietPower
Evaluation Board for Active EMI Filters
相關PDF資料 |
PDF描述 |
|---|---|
| QPI-4L | 7 Amp Active EMI Filter for 48 V DC Bus |
| QPI-5-EVAL1 | Evaluation Board for Active EMI Filters |
| QPI-6-EVAL1 | Evaluation Board for Active EMI Filters |
| QPO-1L | Output Ripple Attenuation SiP |
| QPO-1Q | Output Ripple Attenuation SiP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPI-3L | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:ACTIVE EMI FILTER |
| QPI-3LZ | 制造商:Vicor Corporation 功能描述:24V 7A ACTIVE EMI FILTER 制造商:Vicor Corporation 功能描述:QPI Series 10 - 40 Vin 7 A Open Frame Active EMI Filter 制造商:VICOR CORPORATION 功能描述:QPI Series 10 - 40 Vin 7 A Open Frame Active EMI Filter |
| QPI-3LZ-01 | 制造商:Vicor Corporation 功能描述:24V 7A ACTIVE EMI FILTER OPN FRM 制造商:Vicor Corporation 功能描述:QPI Series 10 - 40 Vin 7 A Open Frame Active EMI Filter w/ Hot Swap 制造商:VICOR CORPORATION 功能描述:QPI Series 10 - 40 Vin 7 A Open Frame Active EMI Filter w/ Hot Swap |
| QPI-4-CB1 | 制造商:Vicor Corporation 功能描述:DOSA Compliant Evaluation for 'QPI-4LZ Series |
| QPI-4-EVAL1 | 制造商:Vicor Corporation 功能描述:QPI-4LZ Evaluation Board w/ Terminal Blocks |
發布緊急采購，3分鐘左右您將得到回復。