- 您現在的位置：買賣IC網 > PDF目錄382397 > PXAG39KBA (NXP SEMICONDUCTORS) XA 16-bit microcontroller family XA 16-bit microcontroller 32K FLASH/1K RAM, watchdog, 2 UARTs PDF資料下載
參數資料
| 型號： | PXAG39KBA |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | XA 16-bit microcontroller family XA 16-bit microcontroller 32K FLASH/1K RAM, watchdog, 2 UARTs |
| 中文描述： | 16-BIT, FLASH, 30 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 12/42頁 |
| 文件大?。?/td> | 217K |
| 代理商： | PXAG39KBA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Philips Semiconductors
Preliminary data
XA-G39
XA 16-bit microcontroller family
32K Flash/1K RAM, watchdog, 2 UARTs
2002 Mar 13
12
V
DD
SUPPLY OR +12V
±
5%
5V
±
5%
TxD
RxD
V
SS
V
PP
V
DD
TxD
RxD
RST
XTAL2
XTAL1
SU01593
V
SS
V
CC
2
3
5
FEMALE
DB-9
RS-232
TRANSCEIVER
MC145406, MAX232,
OR EQUIVALENT
FOR USE WITH WINISP OR FLASHMAGIC
Figure 4. In-System Programming with a Minimum of Pins
In-System Programming (ISP)
In-System Programming (ISP) is performed without removing the
microcontroller from the system. The In-System Programming (ISP)
facility consists of a series of internal hardware resources coupled
with internal firmware to facilitate remote programming of the
XA-G39 through the serial port. This firmware is provided by Philips
and embedded within each XA-G39 device.
The Philips In-System Programming (ISP) facility has made in-circuit
programming in an embedded application possible with a minimum
of additional expense in components and circuit board area.
The ISP function uses five pins: TxD, RxD, V
SS
, V
DD
, and V
PP
(see
Figure 4). Only a small connector needs to be available to interface
your application to an external circuit in order to use this feature.
The V
PP
supply should be adequately decoupled and V
PP
not
allowed to exceed datasheet limits.
V
CC
5.0 V
V
PP
5.0 V
OSC FREQ
I
DD
75 mA typical
22 MHz
5.0 V
5.0 V
30 MHz
90 mA typical
ISP increases I
DD
by less than 1mA.
Free ISP software is available on the Philips web site: “WinISP”
1. Direct your browser to the following page:
http://www.semiconductors.com/mcu/download/80C51/flash/
2. Download “WinISP.exe”
3. Execute WinISP.exe to install the software
Free ISP software is also available from the Embedded Systems
Academy: “FlashMagic”
1. Direct your browser to the following page:
http://www.esacademy.com/software/flashmagic/
2. Download Flashmagic
3. Execute “flashmagic.exe” to install the software
There is also an application note available that deals with In-System
Programming (AN716). At www.philipsmcu.com, search for “ISP”,
then select AN716 from the search results.
Using In-System Programming (ISP)
ISP mode is entered by holding PSEN low, asserting, un-asserting
RESET, then releasing PSEN. When ISP mode is entered, the
default loader first disables the watchdog timer to prevent a
watchdog reset from occurring during programming.
The ISP feature allows for a wide range of baud rates to be used in
the application, independent of the oscillator frequency. It is also
adaptable to a wide range of oscillator frequencies. This is
accomplished by measuring the bit-time of a single bit in a received
character. This information is then used to program the baud rate in
terms of timer counts based on the oscillator frequency. The ISP
feature requires that an initial character (a lowercase f) be sent to
the XA-G39 to establish the baud rate. The ISP firmware provides
auto-echo of received characters.
Once baud rate initialization has been performed, the ISP firmware
will only accept specific Intel Hex-type records. Intel Hex records
consist of ASCII characters used to represent hexadecimal values
and are summarized below:
:NNAAAARRDD..DDCC<crlf>
In the Intel Hex record, the “NN” represents the number of data
bytes in the record. The XA-G39 will accept up to 16 (10H) data
bytes. The “AAAA” string represents the address of the first byte in
the record. If there are zero bytes in the record, this field is often set
to 0000. The “RR” string indicates the record type. A record type of
“00” is a data record. A record type of “01” indicates the end-of-file
mark. In this application, additional record types will be added to
indicate either commands or data for the ISP facility. The maximum
number of data bytes in a record is limited to 16 (decimal). ISP
commands are summarized in Table 1.
As a record is received by the XA-G39, the information in the record
is stored internally and a checksum calculation is performed. The
相關PDF資料 |
PDF描述 |
|---|---|
| PXAG49KBA | XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs |
| PXAG49KFA | XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs |
| PXT2222 | NPN switching transistor |
| PXT2907 | PNP switching transistor |
| PXT3904 | NPN switching transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PXAG49 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs |
| PXAG49KBA | 功能描述:16位微控制器 - MCU XA 16BIT 64KF/2KR IN SYS PROG RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PXAG49KBA/00,512 | 功能描述:16位微控制器 - MCU 64K/2K FLISP 30M/LCC44 COM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PXAG49KBBD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family |
| PXAG49KBBD/00,557 | 功能描述:16位微控制器 - MCU 64K/2K FL 16 BIT ISP/IAP COM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發(fā)布緊急采購，3分鐘左右您將得到回復。