- 您現(xiàn)在的位置：買賣IC網 > PDF目錄98066 > PTV12010WAD (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTV12010WAD |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, SIP-8 |
| 文件頁數： | 2/22頁 |
| 文件大小： | 386K |
| 代理商： | PTV12010WAD |
www.ti.com
Capacitor Recommendations for the PTV12010 Series of Power Modules
Input Capacitors
Output Capacitor (Optional)
Ceramic Capacitors
Tantalum Capacitors
SLTS234B – DECEMBER 2004 – REVISED FEBRUARY 2007
The required input capacitors are a combination of a 10-F X5R/X7R ceramic, and a 100-F electrolytic type.
When VO > 3 V the 100-F electrolyitc capacitance must be rated for 700 mArms ripple current capability. For
VO ≤ 3 V, the ripple current rating must be at least 450 mArms. Where applicable, Table 4 gives the maximum
output voltage and current limits for a capacitor's rms ripple current rating. The ripple current requirements for
the electrolytic capacitance are conditional that the 10-F ceramic capacitor is present.
The 10-F ceramic capacitor is necessary to reduce both the magnitude of ripple current through the electroytic
capacitor and the amount of ripple current reflected back to the input source. Ceramic capacitors should be
located within 0.5 in. (1,3 cm) of the module input pins. Additional ceramic capacitors can be added to reduce
the RMS ripple current requirement for the electrolytic capacitor.
Ripple current (Arms) rating, less than 100 m
of equivalent series resistance (ESR), and temperature are the
major considerations when selecting input capacitors. Regular tantalum capacitors have a recommended
minimum voltage rating of 2 × (max. dc voltage + ac ripple). This is standard practice to ensure reliability. Only a
few tantalum capacitors were found to have sufficient voltage rating to meet this requirement. At temperatures
below 0°C, the ESR of aluminum electrolytic capacitors increases. For these applications Os-Con,
polymer-tantalum, and polymer-aluminum types should be considered.
For applications with load transients (sudden changes in load current), regulator response benefits from external
output capacitance. The optional value defined is only required to meet the transient response specification. For
most applications, a high-quality computer-grade aluminum electrolytic capacitor is adequate. These capacitors
provide decoupling over the frequency range, 2 kHz to 150 kHz, and are suitable when ambient temperatures
are above 0°C. For operation below 0°C, tantalum, ceramic, or Os-Con type capacitors are recommended.
When using one or more nonceramic capacitors, the calculated equivalent ESR should be no lower than 4 m
(7 m
using the manufacturer's maximum ESR for a single capacitor). A list of preferred low-ESR type
capacitors are identified in Table 4.
In addition to electrolytic capacitance, adding a 10–F ceramic capacitor across the output will further reduce the
output ripple voltage and improve the regulator's transient response. The measurement of both the output ripple
and transient response is also best achieved across a 10–F ceramic capacitor.
Above 150 kHz, the performance of aluminum electrolytic capacitors is less effective. Multilayer ceramic
capacitors have low ESR and a resonant frequency higher than the bandwidth of the regulator. They are
recommended to reduce the reflected ripple current at the input as well as improve the transient response of the
output. When used on the output their combined ESR is not critical as long as the total value of ceramic
capacitance does not exceed approximately 300 F. Also, to prevent the formation of local resonances, do not
place more than five identical ceramic capacitors in parallel with values of 10 F or greater.
Tantalum-type capacitors can only be used on the output bus, and are recommended for applications where the
ambient operating temperature can be less than 0°C. The AVX TPS, Sprague 593D/594/595 and Kemet
T495/T510 capacitor series are suggested over many other tantalum types due to their higher rated surge,
power dissipation, and ripple current capability. As a caution, many general-purpose tantalum capacitors have
considerably higher ESR, reduced power dissipation and lower ripple current capability. These capacitors are
also less reliable as they have reduced power dissipation and surge current ratings. Tantalum capacitors that
have no stated ESR or surge current rating are not recommended for power applications.
When specifying Os-con and polymer tantalum capacitors for the output, the minimum ESR limit is encountered
before the maximum capacitance value is reached.
10
相關PDF資料 |
PDF描述 |
|---|---|
| PTV12010WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PVX003A0X43-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PVX006A0X43-SRZ | DC-DC REG PWR SUPPLY MODULE |
| PVX006A0X3-SRZ | DC-DC REG PWR SUPPLY MODULE |
| PVX012A0X3-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTV12010WAH | 功能描述:DC/DC轉換器 1.2-5.5V 8A 12V-In WideAdj SIP Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTV12010WAH | 制造商:Texas Instruments 功能描述:IC REG SW 1.2-5.5V 8A VERT T/H 制造商:Texas Instruments 功能描述:IC, REG SW 1.2-5.5V 8A VERT T/H 制造商:Texas Instruments 功能描述:IC, REG SW 1.2-5.5V 8A VERT T/H; DC / DC Converter Type:Non Isolated POLA; DC / DC Converter Output Type:Adjustable; Input Voltage DC Min:10.8V; Input Voltage DC Max:13.2V; No. of Outputs:1; Output Voltage Nom.:1.2V to 5.5V; Output ;RoHS Compliant: Yes |
| PTV12020 | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTV12020L | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTV12020LAD | 功能描述:DC/DC轉換器 28.8W 0.8-1.8V 16A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發(fā)布緊急采購，3分鐘左右您將得到回復。