ELECTRICAL CHARACTERISTICS
SLTS230C – NOVEMBER 2004 – REVISED SEPTEMBER 2008...................................................................................................................................... www.ti.com
operating at 25°C free-air temperature, VI = 24 V, VO = 12 V, IO = IO (max), CI = 2× 4.7 F, CO = 100 F (unless otherwise
noted)
PTN78000H
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VO = 12 V
0.1
1.5
IO
Output current
TA = 85°C, natural convection airflow
VO = 15 V
0.1
1.5 (1)
A
VO = 22 V
0.1
1 (1)
VI
Input voltage range
Over IO range
15 (2)
36
V
Set-point voltage tolerance
TA = 25°C
±2% (3)
Temperature variation
–40°C to +85°C
±0.5%
Line regulation
Over VI range
±10
mV
VO
Load regulation
Over IO range
±10
mV
Includes set point, line, load
Total output voltage
±3% (3)
variation
–40°C < TA < 85°C
VI < 19 V
11.85
VI – 3
Output voltage adjust
19 V
≤ VI ≤ 25 V
11.85
VI – 4
VO Adj
V
range
VI > 25 V
11.85
22
VI = 24 V, RSET = 383 k , VO = 12 V
91%
η
Efficiency
VI = 24 V, RSET = 15 k, VO = 15 V
93%
VI = 32 V, RSET = 95.3 , VO = 22 V
94%
Output voltage ripple
20 MHz bandwith
1% VO
V(PP)
IO (LIM)
Current limit threshold
ΔVO = –50 mV, minimum VI
2× IO(max)
A
1 A/s load step from 50% to 100% IOmax
Transient response
Recovery time
200
s
VO over/undershoot
1
%VO
VI increasing
12.2
UVLO
Undervoltage lockout
V
VI decreasing
12
Input high voltage (VIH)
1
Open (4)
V
Inhibit control (pin 3)
Input low voltage (VIL)
–0.1
0.3
Input low current (IIL)
0.25
mA
II (STBY)
Input standby current
Pin 3 connected to GND
17
mA
FS
Switching frequency
Over VI and IO ranges
440
550
660
kHz
CI
External input capacitance
Ceramic
9.4 (5)
F
Nonceramic
100 (6)
F
External output
CO
Ceramic
200
capacitance
Equiv. series resistance (nonceramic)
10 (7)
m
Per Telcordia SR-332, 50% stress,
MTBF
Calculated reliability
8.9
106 Hr
TA = 40°C, ground benign
(1)
The maximum output current is 1.5 A or the maximum output power is 22.5 W, whichever is less.
(2)
For output voltages less than 19 V, the minimum input voltage is 15 V or (VO + 3) V, whichever is greater. For output voltages of 19 V
and higher, the minimum input voltage is (VO + 4) V. See the Application Information section for further guidance.
(3)
The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a
tolerance of 1% with with 100 ppm/°C or better temperature stability.
(4)
This control pin has an internal pullup, and if left open circuit, the module operates when input power is applied. The open-circuit voltage
is typically 1.5 V. A small, low-leakage (< 100 nA) MOSFET is recommended for control. See the Application Information section for
further guidance.
(5)
Two external 4.7-F ceramic capacitors are required across the input (VI and GND) for proper operation. Locate the capacitor close to
the module.
(6)
100 F of output capacitance is required for proper operation. See the Application Information section for further guidance.
(7)
This is the typical ESR for all the electrolytic (nonceramic) capacitance. Use 17 m
as the minimum when using maximum ESR values
to calculate.
4
Copyright 2004–2008, Texas Instruments Incorporated