- 您現在的位置：買賣IC網 > PDF目錄368356 > PTN3331 High speed differential line driver PDF資料下載
參數資料
| 型號： | PTN3331 |
| 英文描述： | High speed differential line driver |
| 中文描述： | 高速差分線路驅動 |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 250K |
| 代理商： | PTN3331 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁
Philips Semiconductors
PTN3331
High speed differential line driver
Product data
Rev. 01 — 06 August 2002
11 of 14
9397 750 08339
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 220
°
C for thick/large
packages, and below 235
°
C small/thin packages.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相關PDF資料 |
PDF描述 |
|---|---|
| PTN3332 | High speed differential line receiver |
| PTN3332D | High speed differential line receiver |
| PTN3332DH | High speed differential line receiver |
| PTPM754DB | 8-BIT MICROCONTROLLER |
| PTS4 | ABISOLIERWERKZEUG 0.2 - 6.0MM2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTN3331D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High speed differential line driver |
| PTN3331D,112 | 功能描述:緩沖器和線路驅動器 HIGH SPEED DIFFER LINE DRIVER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PTN3331D,118 | 功能描述:緩沖器和線路驅動器 HIGH SPEED DIFFER LINE DRIVER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PTN3331DH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High speed differential line driver |
| PTN3331DH,112 | 功能描述:緩沖器和線路驅動器 HIGH SPEED DIFFER LINE DRIVER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。