- 您現在的位置：買賣IC網 > PDF目錄368355 > PTH05000W Fully-integrated linear lighting ballast, IR21571, European version, 230VAC line, 36W/T8 lamp PDF資料下載
參數資料
| 型號： | PTH05000W |
| 英文描述： | Fully-integrated linear lighting ballast, IR21571, European version, 230VAC line, 36W/T8 lamp |
| 中文描述： | 6答：5 - V輸入寬輸出調節插入電源模塊 |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 286K |
| 代理商： | PTH05000W |
For technical support and more information, see inside back cover or visit www.ti.com
Pin Descriptions
Vin:
The positive input voltage power node to the mod-
ule, which is referenced to common GND.
GND:
This is the common ground connection for the
‘V
in
’ and ‘V
out
’ power connections. It is also the 0 VDC
reference for the ‘Inhibit’ and ‘V
o
Adjust’ control input.
Vout:
The regulated positive power output with respect
to the GND node.
Inhibit:
The Inhibit pin is an open-collector/drain negative
logic input that is referenced to GND. Applying a low-
level ground signal to this input disables the module’s
output and turns off the output voltage. When the Inhibit
control is active, the input current drawn by the regulator
is significantly reduced. If the Inhibit pin is left open-
circuit, the module will produce an output whenever a
valid input source is applied.
Vo Adjust:
A 0.1 W, 1 % 100 ppm/°C resistor must be
connected between this pin and the GND pin to set the
output voltage to the desired value. The set point range
for the output voltage is from 0.9 V to 3.6 V. The resistor
required for a given output voltage may be calculated
from the following formula. If left open circuit, the
module output will default to its lowest output voltage
value. For further information on the adjustment and/or
trimming of the output voltage, consult the related appli-
cation note.
R
set
= 10 k
·
0.891 V
V
out
– 0.9 V
– 3.24 k
The specification table gives the preferred resistor values
for a number of standard output voltages.
Ordering Information
Output Voltage
(PTH05000 xx)
Code
Voltage
W
0.9 V – 3.6 V (Adjust)
Package Options
(PTH05000x
Code
Description
AH
Horiz. T/H
AS
SMD, Standard
(3)
)
(1)
Pkg Ref.
(2)
(EUS)
(EUT)
Notes:
(1) Add “T” to end of part number for tape and reel on SMD packages only.
(2) Reference the applicable package reference drawing for the dimensions and PC board layout
(3) “Standard” option specifies 63/37, Sn/Pb pin solder material.
6-A, 5-V Input Non-Isolated
Wide-Output Adjust Power Module
SLTS201B
–
MAY 2003
–
REVISED AUGUST 2003
PTH05000 Series
—
5-V Input
相關PDF資料 |
PDF描述 |
|---|---|
| PTH12000W | 32W Fully-integrated linear lighting ballast, IR21571, U.S. version, 120VAC line, 32W/T8 lamp |
| PTH12030W | Universal Input Linear Fluorescent Ballast using the IR2167 |
| PTH8C16TBB101M | Universal Input Linear Fluorescent Ballast using the IR2166 |
| PTH8C16TBB221M | Mini-ballast for single 25W compact fluorescent ballast, European version with 230VACin |
| PTH8C16TBB330M | Intelligent Power Switch 1 Channel Low Side Driver in a SOT-223 Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH05000WAD | 功能描述:DC/DC轉換器 6A 5VInput Wide-Out Adj Plug-in Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH05000WAH | 功能描述:DC/DC轉換器 6A 5VInput Wide-Out Adj Plug-in Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH05000WAH | 制造商:POWER TRENDS 功能描述:IC DC/DC 5VIN 6A ADJ O/P 5000 |
| PTH05000WAH | 制造商:Texas Instruments 功能描述:Supply Voltage Max.:5.5V |
| PTH05000WAS | 功能描述:DC/DC轉換器 6A 5VInput Wide-Out Adj Plug-in Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。