- 您現在的位置：買賣IC網 > PDF目錄224860 > PT7A6526 50V Fast Recovery Diode in a DO-203AB (DO-5) package PDF資料下載
參數資料
| 型號： | PT7A6526 |
| 英文描述： | 50V Fast Recovery Diode in a DO-203AB (DO-5) package |
| 中文描述： | 單通道協議控制器？ |用戶手冊PT7A6525（6）在中斷演示模式？（PDF格式系統） |
| 文件頁數： | 4/41頁 |
| 文件大?。?/td> | 1640K |
| 代理商： | PT7A6526 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
12
PT Pericom Technology Inc.
The Demo Board of PT7A6525
in DMA Mode
The Hardware Configuration of the
Demo Board
Component on the demo board
Shown in Figure 1, there are some jumpers, connector
and button which are configured by user.
To connect the circuit correctly, there are 4 pins in
jumper set X5 should be connected. The pin “RxDA”
and the pin “TxDA” is connected to each other by
jumper, and so does the pin “RxDB” and the pin
“TxDB”.
The button K1 is for reset. Pressing this button will
reset all the chips on the demo board. After power-on,
a reset is needed before the demo program can run nor-
mally.
X4 is a RS232 9-pin female connector to PC. The pin
definition is shown in “Function Description - RS232
Serial Interface”. This connector is connected to the
COM1 or COM2 port of PC. After the demo program
starts to run, it will check the port which the demo
board is connected to.
There is a power port on the board. One pin of the port
is for VCC and another for GND. VCC is a +5V power.
The range of VCC is 4.5V to 5.5V. A supply voltage
beyond this range may cause damage on the demo
board. The pin definition is shown in Figure 1.
Connect the Hardware
Before the demo program on PC is run, the demo board
should be connected to power source.
The X4 should be connected to the COM1 or COM2
port of PC by RS232 cable with correct pin-connec-
tions. The baud rate of COM1 is 9600 bps which is set
by the Demo Program. The serial port is of no parity
check, eight data bit, and one stop bit.
After the power-on of the demo board, press button K1
to generate the reset signal.
相關PDF資料 |
PDF描述 |
|---|---|
| PT7A6527 | 60V Single N-Channel Hi-Rel MOSFET in a TO-204AE package |
| PT7A7511 | 4.63V Reset Active Low Supervisor? |
| PT7A7512 | 4.38V Reset Active Low Supervisor? |
| PT7A7513 | 3.08V Reset Active Low Supervisor? |
| PT7A7514 | 300V Single N-Channel HEXFET Power MOSFET in a SO-8 package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT7A6527 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Quad-channel Protocol Controller? | Demo board Schematic and Program?(PDF) |
| PT7A6632 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PT7A6632 32-Channel HDLC Controller |
| PT7A6632J | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PT7A6632 32-Channel HDLC Controller |
| PT7A7511 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4.63V Reset Active Low Supervisor? |
| PT7A7512 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4.38V Reset Active Low Supervisor? |
發布緊急采購，3分鐘左右您將得到回復。