- 您現在的位置：買賣IC網 > PDF目錄66056 > PT6932C (TEXAS INSTRUMENTS INC) 6 A SWITCHING REGULATOR, 725 kHz SWITCHING FREQ-MAX, SMA23 PDF資料下載
參數資料
| 型號： | PT6932C |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 6 A SWITCHING REGULATOR, 725 kHz SWITCHING FREQ-MAX, SMA23 |
| 封裝： | ROHS COMPLIANT, SMD-23 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 180K |
| 代理商： | PT6932C |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
PT6920/PT6930 Series
Using the Standby Function on the PT6920 and
PT6930 Dual Output Voltage Converters
Both output voltages of the 23-pin PT6920/6930 dual
output converter may be disabled using the regulator’s
standby function. This function may be used in applications
that require power-up/shutdown sequencing, or wherever
there is a requirement to control the output voltage On/
Off status with external circuitry.
The standby function is provided by the STBY* control
(pin 3). If pin 3 is left open-circuit the regulator operates
normally, and provides a regulated output at both Vo1
(pins 12–15) and Vo2 (pins 18–21) whenever a valid supply
voltage is applied to Vin (pins 4, 5, & 6) with respect to
GND (pins 7–11). If a low voltage 2 is then applied to pin 3,
both regulator outputs will be simultaneously disabled and
the input current drawn by the ISR will typcially drop to
less than 30mA (50mA max). The standby control may also
be used to hold-off both regulator outputs during the pe-
riod that input power is applied.
The standby pin is ideally controlled using an open-collector
(or open-drain) discrete transistor (See Figure 1). It may
also be driven directly from a dedicated TTL3 compatible
gate. Table 1 provides details of the threshold requirements.
Table 1 Inhibit Control Thresholds 2,3
Parameter
Min
Max
Enable (VIH)
1.8V
Vin
Disable (VIL)
–0.1V
0.8V
Notes:
1. The Standby/Inhibit control logic is similar for all
Power Trends’ modules, but the flexibility and
threshold tolerances will be different. For specific
information on this function for other regulator
models, consult the applicable application note.
2. The Standby control pin is ideally controlled using an
open-collector (or open-drain) discrete transistor and
requires no external pull-up resistor. To disable the
regulator output, the control pin must be pulled to
less than 0.8Vdc with a low-level 0.5mA sink to
ground.
3. The Standby input on the PT6920/6930 series may
be driven by a differential output device, making it
directly compatible with TTL logic. The control
input has an internal pull-up to the input voltage Vin.
A voltage of 1.8V or greater ensures that the
regulator is enabled. Do not use devices that can drive
the Standby control input above 5.5V or Vin.
Figure 1
Turn-On Time:
Turning Q1 in Figure 1 off removes the low-
voltage signal at pin 3 and enables both outputs from the
PT6920/6930 regulator. Following a delay of about 10–20ms,
Vo1 and Vo2 rise together until the lower voltage, Vo2,
reaches its set output. Vo1 then continues to rise until both
outputs reach full regulation voltage. The total power-up
time is less than 25ms, and is relatively independant of load,
temperature, and output capacitance. Figure 2 shows wave-
forms of the output voltages Vo1 and Vo2, for a PT6931
(3.3V/2.5V). The turn-off of Q1 corresponds to the rise in
Vstby. The waveforms were measured with a 5Vdc input
voltage, and with resistive loads of 5A and 2A at the Vo1
and Vo2 outputs respectively.
Figure 2
C
1
+
C
2
+
Inhibit
V
in
V
2 out
COM
Q1
BSS138
+5V V
in
PT6921
18 - 21
23
7 - 11
4,5,6
Vin
V2
out
GND
Vo
2(adj)
V
1(sns)
1
16
V0
1(adj)
12 - 15
V1
out
V
2(sns)
22
STBY
3
V
1 out
C
3
+
Vo1 (3.3V)
Vo2 (2.5V)
Vstby
Ch1 1V/Div
Ch2 1V/Div
Ch3 5V/Div
Timebase: 5ms/Div
相關PDF資料 |
PDF描述 |
|---|---|
| PT6932N | 6 A SWITCHING REGULATOR, 725 kHz SWITCHING FREQ-MAX, SMA23 |
| PT6933N | 6 A SWITCHING REGULATOR, 725 kHz SWITCHING FREQ-MAX, SMA23 |
| PT7675C | 30 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, MSMA18 |
| PT7675N | 30 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, MSMA18 |
| PT7675A | 30 A SWITCHING REGULATOR, 350 kHz SWITCHING FREQ-MAX, MSMA18 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT6932N | 功能描述:DC/DC轉換器 25W 5V-Input Adj Dual Output ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT6933 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:8-A 5V-Input Dual-Output Integrated Switching Regulator |
| PT6933A | 功能描述:DC/DC轉換器 25W 5V-Input Adj Dual Output ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT6933C | 功能描述:DC/DC轉換器 25W 5V-Input Adj Dual Output ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT6933N | 功能描述:開關變換器、穩壓器與控制器 25W 5V-Input Adj Dual Output ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。