
For technical support and more information, see inside back cover or visit www.ti.com
PT6360 Series
11 A 12-V Input Adjustable
Integrated Switching Regulator
Performance Specifications (Unless otherwise stated, Ta =25 °C, Vin =12 V, Cin =560 F, Cout =0 F, and Io =Iomax)
PT6360 SERIES
Characteristics
Symbols
Conditions
Min
Typ
Max
Units
Output Current
Io
Vin =12 V
Vo < 3.3 V
0
—
11
A
Vo ≥ 3.3 V
0
—
10
Input Voltage Range
Vin
Over Io range
10.8
—
13.2
V
Set-Point Voltage Tolerance
Vo tol
—
±2
%Vo
Temperature Variation
Regtemp
–40 °C <Ta < +85 °C
—
±0.5
—
%Vo
Line Regulation
Regline
Over Vin range
—
±3
—
mV
Load Regulation
Regload
Over Io range
—
±5
—
mV
Total Output Variation
Regtot
Includes set-point, line, load,
——±3
%Vo
–40 °C
≤ Ta ≤ +85 °C
Efficiency
η
Io =8 A
PT6361 ( 5 V)
—
93
—
PT6362 (3.3 V)
—
91
—
PT6363 (2.5 V)
—
90
—
PT6364 (1.8 V)
—
87
—
%
PT6365 (1.5 V)
—
85
—
PT6366 (1.2 V)
—
82
—
PT6367 (1.0 V)
—
80
—
Vo Ripple (pk-pk)
Vr
20 MHz bandwidth
Vo = 5.0 V
—
50
—
Vo = 3.3 V
—
25
—
mVpp
Vo ≤ 2.5 V
—
15
—
Transient Response
1 A/s load step, 50 to 100 % Iomax,
Cout =330 F
ttr
Recovery Time
—
50
—
Sec
Vtr
Vo over/undershoot
—
70
—
mV
Over-Current Threshold
ITRIP
Reset, followed by auto-recovery
—
16
—
A
Output Voltage Adjust
Vo adj
With Vo Adjust
—
±15 (1)
—%
Switching Frequency
s
Over Vin and Io ranges
300
350
400
kHz
Inhibit Control (pin1)
Referenced to GND (pins 5–8)
Input High Voltage
VIH
2
—
Open (2)
V
Input Low Voltage
VIL
–0.2
—
0.3
Input Low Current
IIL
Pin 1 to GND
—
–10
—
A
Standby Input Current
Iin standby
Pin 1 to GND
—
5
—
mA
External Input Capacitance
Cin
560 (3)
——F
External Output Capacitance
Cout
0
330 (4)
5,000
F
Operating Temperature Range
Ta
Over Vin range
–40
—
85 (5)
°C
Solder Reflow Temperature
Treflow
Surface temperature of pins or case
—
215 (6)
°C
Storage Temperature
Ts
—
–40
—
125
°C
Reliability
MTBF
Per Bellcore TR-332
8.0
—
106 Hrs
50% stress, Ta =40°C, ground benign
Mechanical Shock
Mil-STD-883D, Method 2002.3
—
500
—
G’s
Half Sine, mounted to a fixture
Mechanical Vibration
Mil-STD-883D, Method 2007.2,
—
20 (7)
—G’s
20-2000 Hz, PCB mounted
Weight
—
10
—
grams
Flammability
—
Materials meet UL 94V-0
Notes: (1) This is a typical value. For the adjustment limits of a specific model consult the related application note on output voltage adjustment.
(2) The Inhibit control (pin 1) has an internal pull-up to Vin, and if left open-circuit the module will operate when input power is applied. A small low-
leakage (<100 nA) MOSFET is recommended to control this input. See application notes for more information.
(3) A 560 F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimumm of 1.3 Arms of ripple current.
(4) An external output capacitor is not required for basic operation. Adding 330F of distributed capacitance at the load will improve the transient response,
and reduce output ripple voltage.
(5) See SOA curves or consult factory for the appropriate derating.
(6) During solder reflow of SMD package version do not elevate the module case, pins, or internal component temperatures above a peak of 215 °C. For
further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products,” (SLTA051).
(7) The case pins on the through-hole package types (suffixes N & A) must be soldered. For more information see the applicable package outline drawing.
SLTS179A - JANUARY 2003 - REVISED APRIL 2003